Pelican TH-50VX100U - Manual (Page 7)

7
Safety Precautions / Maintenance
WARNING
The front of the display panel has been specially treated. Wipe the panel surface gently using only a cleaning
cloth or a soft, lint-free cloth.
• If the surface is particularly dirty, wipe with a soft, lint-free cloth which has been soaked in pure water or water in
which neutral detergent has been diluted 100 times, and then wipe it evenly with a dry cloth of the same type until
the surface is dry.
• Do not scratch or hit the surface of the panel with fingernails or other hard objects, otherwise the surface may
become damaged. Furthermore, avoid contact with volatile substances such as insect sprays, solvents and thinner,
otherwise the quality of the surface may be adversely affected.
If the cabinet becomes dirty, wipe it with a soft, dry cloth.
• If the cabinet is particularly dirty, soak the cloth in water to which a small amount of neutral detergent has been
added and then wring the cloth dry. Use this cloth to wipe the cabinet, and then wipe it dry with a dry cloth.
• Do not allow any detergent to come into direct contact with the surface of the Plasma Display. If water droplets get
inside the unit, operating problems may result.
• Avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the
cabinet surface may be adversely affected or the coating may peel off. Furthermore, do not leave it for long periods
in contact with articles made from rubber or PVC.
Maintenance
Setup
Do not place the Plasma Display on sloped or
unstable surfaces.
• The Plasma Display may fall off or tip over.
Do not place any objects on top of the Plasma
Display.
• If water spills onto the Plasma Display or foreign
objects get inside it, a short-circuit may occur which
could result in fire or electric shock. If any foreign
objects get inside the Plasma Display, please consult
an Authorized Service Center.
Do not cover the ventilation holes.
• Doing so may cause the Plasma Display to overheat,
which can cause fire or damage to the Plasma Display.
Transport only in upright position!
• Transporting the unit with its display panel facing
upright or downward may cause damage to the
internal circuitry.
If using the pedestal (optional accessory), leave a space
of 3
15
/
16
” (10 cm) or more at the top, left and right,
and 2
3
/
4
” (7 cm) or more at the rear, and also keep the
space between the bottom of the display and the floor
surface. If using some other setting-up method, follow
the manual of it. (If there is no specific indication of
installation dimension in the installation manual, leave
a space of 3
15
/
16
” (10 cm) or more at the top, bottom,
left and right, and 2
3
/
4
” (7 cm) or more at the rear.)
An apparatus with CLASS I construction shall be
connected to a mains socket outlet with a protective
earthing connection.
AC Power Supply Cord
The Plasma Display is designed to operate on 110 - 127 V
AC, 50/60 Hz.
Do not use any power supply cord other than that
provided with this unit.
• Doing so may cause fire or electric shocks.
Securely insert the power cord plug as far as it will go.
• If the plug is not fully inserted, heat may be generated
which could cause fire. If the plug is damaged or the
wall socket plate is loose, they should not be used.
Do not handle the power cord plug with wet hands.
• Doing so may cause electric shocks.
Do not do anything that might damage the power cable. When
disconnecting the power cable, hold the plug, not the cable.
• Do not make any modifications, place heavy objects
on, place near hot objects, heat, bend, twist or
forcefully pull the power cable. Doing so may cause
damage to the power cable which can cause fire or
electric shock. If damage to the cable is suspected,
have it repaired at an Authorized Service Center.
If the Plasma Display will not be used for a long period
of time, unplug the power cord from the wall outlet.
If problems occur during use
If a problem occurs (such as no picture or no sound),
or if smoke or an abnormal odor is detected from the
Plasma Display, unplug the power cord immediately.
• Continuous use of the Display under these conditions
might cause fire or permanent damage to the unit.
Have the Display evaluated at an Authorized Service
Center. Services to the Display by any unauthorized
personnel are strongly discouraged due to its high
voltage dangerous nature.
If water or foreign objects get inside the Plasma Display, if
the Plasma Display is dropped, or if the cabinet becomes
damaged, disconnect the power cord plug immediately.
• A short may occur, which could cause fire. Contact an
Authorized Service Center for any repairs that need to be made.