Tuning the tv to your unit, To change the rf output channel, Getting star ted – Panasonic VP-31GN User Manual

Page 11: 3] press [menu, 1] hold down [menu] for 5 seconds or more, 2] press [ch, 4] press [menu] to exit the setting mode, ª to restart plug in auto tuning

Getting Star

ted

Tuning the TV to Your Unit

The unit supplies a signal to the TV via the RF coaxial cable on channel E21

s69. It is possible to view the unit’s picture on your TV in the

same way that you watch TV broadcasts. The unit is fitted with its own tuner (just like a normal TV) and can be preset to receive up to 99 TV
broadcast stations.
≥Switch [VHS/TV/DVD] to “VHS”.
¬ If you have connected the unit to the TV through the audio/video output sockets
You do not need to follow the procedure below. To view the pictures from the unit, set to the AV mode on the TV with [AV].

When the unit is turned on after connecting the aerial cable and
the mains lead for the first time, tuning starts automatically.
≥If the unit is turned on with the aerial not connected, all channels are

skipped.

[1]

Press [VHS

Í] to turn on this unit.

[2]

Set the TV to an unused position for the

unit viewing channel.

≥Tune the TV until the display shown on the right appears. Refer

also to the TV’s instructions regarding tuning.

≥Set “RF SELECT” with [2 1] to select the colour TV system

used by the TV set to be connected.

BG:

PAL B.G.H/SECAM B.G

PAL I

DK:

PAL D/SECAM D.K.K1

[3]

Press [MENU].

¬ To cancel Auto Tuning partway through
Press [MENU]. Auto Tuning will stop halfway by turning the unit off, pressing [MENU], playback or a
power failure.

¬ If Auto Tuning stops halfway by turning the unit off, playback or a power failure
≥Disconnect the mains lead and then reconnect it.
≥Turn on the unit. Plug in Auto Tuning restarts.

¬ To set the channels manually (

lpage 23)

ª To restart Plug in Auto Tuning

≥Turn the unit on.
≥Make sure there is no video cassette in the unit.
1) Keep

both

[CH]

I and J on the unit pressed simultaneously for 3

seconds or more until the channel on the unit’s display changes to 1.

2) Disconnect the mains lead and then reconnect it.
3) Turn on the unit. Plug in Auto Tuning restarts.

You can change the RF output channel, for example, when interference occurs on the picture after tuning.

..........................................................................................................................................................................................................................................................................................................................................

[1] Hold down [MENU] for 5 seconds or more.

[2] Press [CH]

to select the channel

(E21

sE69).

≥Each time you press [CH]

IJ (l left)

≥Set to “ss” (RF OFF) when you use the audio/video cable for the

connection.

≥You can also use the numeric buttons.

Example: “28”; [2]

l[8]

[3] Retune your TV to the new RF channel for

the unit.

[4] Press [MENU] to exit the setting mode.

Note:
≥Even if the RF output channel has been changed, it is not necessary to perform Auto Tuning.

REW

PULL-OPEN

EJECT

TIMER REC

TAPE REFRESH

AV2 IN

REC/OTR

VIDEO

AUDIO

VHS/DVD/TV

VHS/DVD QUICK REPLAY DUBBING

REC

VOLUME

VHS

DVD

SLOW/SEARCH

NAVI

TOP MENU

RETURN

PROG/CHECK

PROG PLAY

DISPLAY

JET REW

TIMER

ENTER

PLAY
LIST

INDEX/SKIP

OUTPUT

TRACKING/V-LOCK

DIRECT

NAVIGATOR

VHS/DVD

-/- -

VHS

VHS/
TV/
DVD

Numeric

buttons

Plug in Auto Tuning

To change the RF output channel

CH 22

SEARCH

END: MENU

AUTO TUNING
IN PROGRESS,
PLEASE WAIT.

END: MENU

RF SELECT:

RF SELECT

≥ BG I

≥

AUTO TUNING IS
COMPLETED.

Disappears

Panasonic

END: MENU

RF SELECT:

RF SELECT

≥ BG I

≥

(RF OFF)

VP31GCGCS.book 11 ページ２００３年７月３０日　水曜日　午後８時２８分