Philips DVP3345VB - Manual (Page 26)

EN - 26
English 26 Timer Recording (cont’d)
When a Timer Recording ends
● The DVD/VCR will turn off and “ ” on the DVD/VCR’s display panel will
flash indicating that the recording is complete, then goes into the timer
standby mode again. (It may switch to DVD mode automatically.) At this
point, you cannot use the VCR unless you release the DVD/VCR from the
timer standby mode.
To release the DVD/VCR from timer standby mode
● If the DVD component is active and no more Timer Recordings are on
standby, you can cancel the timer standby mode by pressing TIMER SET or
VCR on the remote control or by pressing SOURCE or STOP/EJECT C A
on the front panel.
● If the DVD component is not active, or the “ ” is not flashing but lit
indicating there are more Timer Recordings on standby, you can cancel the
timer standby mode only by pressing TIMER SET on the remote control or
by pressing STOP/EJECT C A on the front panel.
● After releasing the DVD/VCR from timer standby mode, you can use it as usual.
Canceling a Timer Recording Before the Recording Starts
7
Press ▲ or ▼ to select a recording tape speed. The arrow will
appear beside your choice. The selected speed will flash beside REC
SPEED. Details about tape speed are on page 58.
You must select the recording speed to complete the timer
programming.
8
Press CLEAR to remove the menu.
9
Press TIMER SET.
● In some cases, the DVD/VCR will switch to DVD mode instead. You
may use the DVD player during a Timer Recording.
● If you want to use the VCR until time for the recording, don’t press
TIMER SET until a few minutes before the recording should start. Or,
press TIMER SET only when you know you won’t be using the VCR
anymore (until after the recording).
● When “ ” is lit (not flashing), you cannot put the DVD/VCR in VCR mode
by pressing VCR or SOURCE. You must first press TIMER SET on the
remote control or STOP/EJECT C A on the front panel to cancel the
Timer Recording temporarily. Then, you can use the VCR features again.
1
Press VCR, then press SETUP so MENU appears.
2
Press ▲ or ▼ to select TIMER PROGRAMMING, then press ►.
3
Press ▲ or ▼ to find the program you want to cancel.
4
While the program number is flashing, press ◄ to clear all the
information for that program.
5
Press CLEAR to remove the menu.
Helpful Hint
• To stop a started Timer Recording,
press STOP/EJECT C A on the front of
the DVD/VCR. (You cannot stop a
started Timer Recording with STOP C
on the remote.)
• To change incorrect information, press
◄ or ► to choose the item you want
to change. Press ▲ or ▼ to adjust the
information.
• If there is no tape in the VCR when
you press TIMER SET, “ ” will flash.
Insert a tape.
• If one or more Timer Recordings are
on standby when one Timer Recording
ends, the DVD/VCR will turn off
automatically and “ ” will appear on
the DVD/VCR’s display panel indicating
that it is now ready for another Timer
Recording.
DVD VCR SETUP
INPUT MENU
REC SPEED MODE
ANGLE SEARCH REPEAT
DISPLAY SUBTITLE ZOOM
TIMER SET
REPEAT
A-B
AUDIO
BACK PAUSE STOP
PLAY
OK
FFW REW
CLEAR TITLE
DISC
TRACKING
OPEN/CLOSE
1 2
6 5 4
7 8 9
0 +10
3
9
7
8
DATE
START TIME
END TIME
WED
1
REC SPEED
PROGRAM NUMBER
ONE TIME PROGRAM
E8E2CCD_E8E2CCH_EN_v1.book Page 26 Friday, March 9, 2012 6:37 PM