Kenwood MD-2070 - Manual (Page 52)

DMF-9020/MD-2070 (En)
52
In case of difficulty
Action Meaning Displayed Message
NO DISC
UNLOCK
SCMS ON
NotAudio
DISC FULL
TITLE FULL
BLANK DISC
NO TRACKS
READING
WRITING
DISC ERROR
EDIT NOW!
CAN’T EDIT
ok? (blinking)
PROTECTED
PLAY ONLY
CAN’T ACCESS
CAN’T LOAD
CDtext EMPTY
Now Analog In
NO TEXT COPY
Displayed messages and actions to be taken against them
÷ Load a disc.
÷ The digital cord or optical fiber cable is not
locked in position or connected incompletely (or
not connected).
0
÷ Use analog recording. §
÷ Use analog recording. §
÷ Use another recordable disc.
÷ More than 255 tracks cannot be recorded per
disc.
÷ Refer to ”Total number of title characters”.
t
÷ When playback is required, use a recorded disc.
÷ The disc can be used for recording without any
problem.
÷ This is a normal operation.
÷ This is a normal operation.
÷ Erase all tracks by executing ”_+ALL”. If this is
not possible, use another Mini Disc. w
÷ This is a normal operation.
÷ Perform editing following the restrictions.
÷ Press the ENTER key to execute editing.
÷ Release the “WRITE PROTECT” condition.
8
÷ Load a recordable Mini Disc.
÷ Connect the unit with a KENWOOD CD text-
compatible CD player using the synchro cord
and optical cable.
0
÷ Load a CD text-compatible disc in the CD player.
÷ Connect the CD player through an optical cable
and set the REC INPUT of the MD recorder
accordingly.
0
÷ Switch the program mode of the CD player off
and put both the CD player and MD recorder in
stop mode.
÷ Use a CD containing CD text.
÷ Use a CD containing CD text.
÷ Set the REC INPUT to the digital input to which
the CD player is connected. •
÷ The CD text of the current disc cannot be
copied. (Use a copy-capable CD disc.)
÷ This unit is not loaded with disc.
÷ The digital cord or optical fiber cable is not
locked in position or connected incompletely (or
not connected).
÷ An attempt is made to record digital signal from
a source while its digital copy has been prohib-
ited by SCMS.
÷ The digital signal being input is not an audio
signal.
÷ There is no recordable area on the disc.
÷ An attempt is made to record a 256th track.
÷ An attempt is made to assign a title with more
characters than usable.
÷ The disc does not contain any recordings.
÷ The disc does not contain any tracks but has a
disc title.
÷ The TOC*1 data of the disc is being read.
÷ The data related to editing or recording is being
written in the disc.
÷ The contents of UTOC*2 are abnormal.
÷ The editing operation is in progress.
÷ An attempt is made to perform editing beyond
the restrictions, for example to erase a track
which is too short.
÷ This is a message for confirming if editing can
really be executed.
÷ The Mini Disc is in the “WRITE PROTECT”
condition.
÷ A playback-only Mini Disc is loaded.
÷ A CD text-compatible CD player is not con-
nected to this unit.
÷ The disc loaded in the CD player is not CD text-
compatible.
÷ The CD player is not connected to this unit
through an optical cable.
÷ The CD player is in play mode or in the program
mode.
÷ The CD in use is not a CD text disc.
÷ No CD is loaded in the player.
÷ The current input mode is the analog mode.
÷ The CD text of certain discs cannot be copied.