Scag Power Equipment STT - Manual (Page 16)

12
Fuel Tank ................................................................................... 10-Gallon Seamless Polyethylene Tank with Large opening and
................................................................................................... Fuel Gauge Fill Cap
Tire Pressure:
Front Caster ........................................................................... 25 PSI
Drive ...................................................................................... 12 PSI
Seat ............................................................................................ Padded, Thick Cushion with tall back rest
Travel Speed:
Forward ................................................................................. 0-10 MPH, 0-12 MPH for 29DFI, 35BVAC, 35BV Only
Reverse .................................................................................. 0-5 MPH, 0-6 MPH for 29DFI, 35BVAC, 35BV Only
3.4 CUTTER DECK
Type: .......................................................................................... Floating, Adjustable, Anti-scalping, Hybrid Design Combines
Out-front and Belly-mount Designs
Construction: ............................................................................. 10-gauge steel reinforced with 7-gauge (3/16") Support Plate.
7-gauge (3/16") deck skirt.
True Cutting Width: ................................................................... 52" (132.0 cm), 61" (155.0 cm), 71.5" (181.6 cm)
Cutting Height Adjustment: ....................................................... Foot Operated Lever Adjustment from Operator's Seat, 1.00" to
6.00" in 1/4"increments
Cutter Blades: ............................................................................. .197 or .250 Thick, Milled Edge, Wear Resistant Marbain™
SMT 52V: Three (3) 18" blades
SMT 61V: Three (3) 21" blades
SMT 72A: Three (3) 24-1/2" blades
Blade Engagement: ................................................................... Electric Blade Engagement Clutch with Control Panel Switch
Connected to the Cutter Deck Gearbox through a Drive Shaft.
Discharge Opening: ................................................................... Extra Wide 11.5" Discharge Opening with Spring Loaded
Discharge Chute
Discharge Chute..................................................................................Black, Polypropylene (Plastic), Flexible
Caster Wheels: ........................................................................... 13x 5.00 Four-Ply (52"), 13 X 6.00 Four-Ply (61" & 72")
Spindles: .................................................................................... Heavy-duty 1-1/8" Top Dimension Spindle Shaft, Cast Housing,
Taper Roller Bearing, Low Maintenance with Top Access Grease
Fitting and Grease Overfill Relief Poppet
Spindle Pulleys: .......................................................................... Split Steel with Easily Removed Taper Hubs
Cutter Deck Belts: ...................................................................... B-section with Kevlar Cord. Self-adjusting, Self-tightening
SMT52 ................................................................................... Scag Part Number - 482281
SMT61 ................................................................................... Scag Part Number - 481558
SMST72 ................................................................................. Scag Part Number - 481980
Electric Clutch Type ................................................................... Ogura Electric Clutch
Drive Shaft ................................................................................. Clamp Yoke Shaft With Two High Speed U-Joints
3.6 HYDRAULIC SYSTEM
Hydraulic Oil Filter ..................................................................... 10 Micron Spin-on Element Type
Hydraulic Reservoir ................................................................... Nylon; 3 Quart Capacity
3.7 WEIGHTS AND DIMENSIONS SMT52V SMT61V SMT72A
Length 82.5" 87.5" 90"
Tracking Width 52" 55" 55"
Overall Width 62" 72" 83.5"
Overall Height 46" 46" 46"
Operating Weight 1200# 1298# 1348#
Section 3
3.8 PRODUCTIVITY
The following chart will aid you in determining how many acres your Scag mower will cut per day.
The chart is an estimate based on 8 hours per day cutting time at 7 MPH with an allowance for overlap and turns.
Cutting Width: 52" 61" 72"
Acres Per Day: 23 27 32
3.3 TRACTOR (CONT'D)
-NOTE-
The machine will travel at 10-12mph for transport purposes.
For best cutting performance the forward travel speed should
be adjusted depending upon the cutting conditions.