English 7 english, Continued – Sherwood R-772 User Manual

Page 7

ENGLISH

Continued

�

Relationship between the video input signal and the video output signal

: Component video signal can be output from the COMPONENT MONITOR OUT jacks only.

In this case, the OSD menu and the momentary OSD cannot be displayed.

: The video signal set in the VIDEO MODE menu can be output from all the types of MONITOR OUT jacks.

: The OSD menu and the momentary OSD cannot be displayed via (COMPOSITE) VIDEO MONITOR OUT jack.

: If the OSD menu operation is performed, the picture is automatically turned off and only the OSD menu is displayed via COMPONENT

MONITOR OUT jacks.

�

Note :

• When outputting the component video signal from the COMPONENT MONITOR OUT jacks as it was input, the momentary

OSD cannot be displayed.

�

HDMI (High Definition Multimedia Interface) connection : (*1)

• You can connect the source component (DVD player, etc.) to the display component (TV, projector, etc.) through this receiver

with using a commercially available HDMI cord.

• The HDMI connection can carry uncompressed digital video signals and digital audio signals.
• The HDMI video stream signals (video signals) are theoretically compatible with DVI-D. When connecting to a TV monitor,

etc., equipped with DVI-D connector, it is possible to connect using a commercially available HDMI-DVI converter cord.

Since the HDMI-to-DVI connection cannot carry any audio signals, you should make audio connections to play the audio
signals on the component equipped with DVI-D connector. (For details, refer to the operating instructions of its.)

• If you connect the HDMI INs to your video components, it is easier to do so following the default settings.
• If your HDMI connection is different from the default setting, you should assign the HDMI INs you used with the "When

selecting the HDMI ASSIGN" procedure on page 54.

• The default settings are as follows :

HDMI 1 : VIDEO 1, HDMI 2 : VIDEO 2

�

Copyright protection system

• This unit supports HDCP (High-bandwidth Digital Contents Protection), technology to protect copyright of digital video signals

against illegal duplication. HDCP must also be supported on the components connected to this unit.

• This unit is HDMI Ver. 1.3 compatible.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI licensing

LLC.

�

Notes :

• For stable signal transfer, we recommend using HDMI cords that are a maximum of 5 meters in length.
• Among the components that support HDMI, some components can control other components via the HDMI connector.

However, this unit cannot be controlled by another component via the HDMI connector.

• The audio signals from the HDMI connector (including the sampling frequency and bit length) may be limited by the

component that is connected.

• The video signals will not be output properly if a component incompatible with HDCP is connected.
• If the resolutions of the video signals which are output from the HDMI MONITOR OUT and your monitor TV are not matched,

the picture is not clear, natural or displayed. In this case, change the setting of the resolution on the source component (DVD
player, etc.) to one which the monitor TV can handle. (For details, refer to the operating instructions of the source
component.)

• When you want to enjoy only the picture on your TV, not the sound, you should set the HDMI AUDIO OUT to OFF not to

output the digital audio signal from the HDMI MONITOR OUT of this receiver. (For details, refer to "When selecting the HDMI
AUDIO OUT" on page 50.)

�

Component video input default settings: (*2)

• If you connect the COMPONENT VIDEO INs to your video components, it is easier to do so following the default settings.
• If your component video connections are different from the default setting, you should assign the COMPONENT VIDEO INs

you used with the “When selecting the VIDEO ASSIGN” procedure on page 54.

• The default settings are as follows:

COMPONENT IN 1 : VIDEO 1, COMPONENT IN 2 : VIDEO 2.

Video input signals

MONITOR OUTs

COMPONENT

S-VIDEO

(COMPOSITE) VIDEO

COMPONENT

S-VIDEO

(COMPOSITE) VIDEO

�

Auto Component

S-Video

Composite video*

�

Component *

Component

Ч��

�

S-Video*

S-Video

�

Composite*

Composite video

�

Auto Component

S-Video

�

Auto Component

Composite video

�

Auto Component*

�

Auto S-Video

S-Video

Composite video*

�

Auto S-Video

S-Video

�

Auto Composite video

Composite video

Video Mode

Setting

�

R-772(A) 2007.8.16 5:21 PM 페이지 7