JVC TH-C90 - Manual (Page 23)

20
The system turns off automatically when the specified period of
time has passed.
Press SLEEP.
Each time you press the button, the shut-off time changes as
follows:
Example:
To check the remaining time
Press SLEEP once.
To change the remaining time
Press SLEEP repeatedly.
To cancel
Press SLEEP repeatedly until “SLEEP – –” appears.
• Turning off the power also cancels the Sleep Timer.
1
Press SPK LEVEL to show the target
speaker indication on the display
window.
Each time you press the button, the indication of the speakers
changes as follows:
2
Press LEVEL +/– to adjust the output
level from –6 to +6.
NOTE
• You can also make adjustments by using the setup menu shown on
the TV screen. (See page 38.)
• The adjustments take effect for all sources other than FM/AM. For
FM/AM, adjust the level separately by repeating the procedure above.
1
Press TREBLE/BASS to show “TRE” or
“BASS” on the display window.
Each time you press the button, the indication alternates
between “TRE” and “BASS”.
• TRE: Select this to adjust treble sound.
• BASS: Select this to adjust bass sound.
2
Press LEVEL +/– to adjust the level from
– 10 to +10 (in 2 steps).
NOTE
• The adjustments take effect for all sources.
The system can be accommodated to your TV’s scan mode.
NOTE
• To use the system in the progressive mode, it is required that the
center unit is connected to the TV by using a component video cord
(not supplied). (See page 13.)
7 While DVD or USB MEMORY is selected as the source and
stopped
1
Press and hold SCAN MODE for
2 seconds.
Currently selected scan mode appears on the display window.
2
Press Cursor 3/2 to select the desired
mode.
• NT. 480I: Select when your TV supports the NTSC
interlaced video input only.
• NT. 480P: Select when your TV equipped with component
jacks supports the NTSC progressive video input.
• PAL. 576I: Select when your TV supports the PAL interlaced
video input only.
• PAL. 576P: Select when your TV equipped with component
jacks supports the PAL progressive video input.
You can get better picture quality in the progressive mode
(“NT. 480P” or “PAL. 576P”) than in the interlace mode
(“NT. 480I” or “PAL. 576I”).
3
Press ENTER while the selected mode is
displayed.
When the progressive mode is selected, the PROGRESSIVE
indicator lights on the display window.
NOTE
• Changing the scan mode does not take effect when connecting the TV
with the S-video or the composite video cord.
• Although the picture may be distorted when you press ENTER, this is
not a malfunction of the system.
Sleep Timer [SLEEP]
– – (off) Z 10 Z 20 Z 30 Z 60 Z 90 Z 120 Z 150 Z
(back to the beginning) (Unit: min.)
Adjusting the output level of
the subwoofer and speakers
FRNT L (Front Left speaker) Z FRNT R (Front Right
speaker) Z CENTER (Center speaker) Z SURR L
(Surround Left speaker) Z SURR R (Surround Right
speaker) Z SUBWFR (Subwoofer) Z (back to the
beginning)
minutes
Adjusting the sound
Changing the scan mode
• There are some progressive TVs and High-Definition TVs that are
not fully compatible with this system, resulting in an unnatural
picture when playing back a DVD VIDEO in the progressive scan
mode. In such a case, change the scan mode to the interlace mode.
• All JVC progressive TVs and High-Definition TVs are fully
compatible with this system.
Basic operations See page 18 for button locations.
EN_TH-C906020[USUGUX].book Page 20 Thursday, June 29, 2006 5:30 PM