FUJITSU SCANSNAP NETWORK SCANNER N1800 - Manual (Page 5)

5
CAUTION
To avoid injuries, do not place the scanner in an
area where small children may be able to reach.
Before moving the scanner, be sure to
disconnect the cables that are connected to the
scanner, and disconnect the power cable from
the AC outlet.
Make sure that the floor is free of any
obstructions.
Moving the scanner with the cable connected to
the computer may damage the cable, in turn
causing fire, electric shock or injuries.
Do not touch the power cable with wet hands.
Doing so may cause an electric shock.
When disconnecting the power cable from the
AC outlet, make sure to hold the power plug and
not the cable.
Pulling the cable may damage it, which may
cause a fire or electric shock.
Do not use the power cable if it is damaged. Also,
do not insert any cables or power plugs into loose
sockets. Doing so may cause a fire or electric
shock.
Be careful of the following when handling the
power cable:
z
Do not moisten, modify, tie, bundle, or wind
the cable.
z Do not place heavy objects on the cable, trap
the cable in a doorway, drop or damage the
cable in any other way.
z Do not pull or forcibly bend or twist the cable.
z Do not place any metal near to the plug of the
power cable.
If the power cable is damaged, contact your
FUJITSU scanner dealer or an authorized
FUJITSU scanner service provider.
Do not place heavy objects on the scanner or
perform other work on top of the scanner. Doing
so might cause injuries or an equipment failure.
Do not use the scanner or AC adapter while it is
covered, for example, with a blanket. Doing so
may raise the temperature inside and cause a
fire.
To avoid injuries, be careful not to get your
accessories (e.g. ties, necklaces) or hair caught
inside the scanner.
Do not touch the heated section such as the
bottom of the scanner or AC adapter for a long
time. Doing so may cause a low-temperature
burn on your skin.
When the scanner is not going to be used for a
long period of time, be sure to disconnect the
power cable from the AC outlet. Not doing so
may cause a fire or electric shock.
Do not use any aerosol sprays or alcohol based
sprays to clean the scanner. Dust blown up by
strong air from the spray may enter the inside of
the scanner. This may cause the scanner to fail
or malfunction. Sparks, caused by static
electricity, generated when blowing off dust and
dirt from the outside of the scanner may cause a
fire.
Check the following items once a month:
z
The power cable is firmly inserted into the AC
outlet.
z The power cable is not emitting abnormal
heat, or the cable is not rusty or bent.
z Dust is not accumulated on the power cable
(especially the plug). If so, wipe off any dust
with a soft, dry cloth.
z The power cable does not have any cracks or
scratches.
If any abnormality is detected, contact your
FUJITSU scanner dealer or an authorized
FUJITSU scanner service provider.
When installing the scanner on a table, make
sure that the work surface is flat and stable, and
that none of the scanner's parts extend over the
table edge, otherwise it may fall over or be pulled
off the table and cause injuries.
Install the scanner away from strong magnetic
fields and other sources of electronic noise.
Protect the scanner against any static electricity
and choose a static-free place to install the
scanner. Static electricity can cause the scanner
to malfunction.
If there is an electrical storm, disconnect the
power cable from the AC outlet.
Not doing so may destroy the scanner, which
may damage your property.
Do not supply the power from the AC outlet
where devices requiring high power such as
copying machines or paper shredders are
connected.
Do not block the ventilation ports. Blocking the
ventilation ports generates heat inside of the
scanner, which may result in a fire or scanner
failure.
Do not use the scanner immediately after moving
it from a cold place into a warm room.
Condensation may occur, which might lead to
scanning errors. Let the scanner dry for one or
two hours before you use it.
When handling documents or the Carrier Sheet,
be careful not to cut your fingers with them.
Do not use a damaged Carrier Sheet because it
may damage or cause the scanner to
malfunction.