Kramer 4x4 Audio and Dante Mixer - Manual (Page 45)

Kramer Electronics Ltd.
FC-404NETxl – Protocol 3000 43
Function Description Syntax Parameters/Attributes Example
X-MIX-LVL Set DSP matrix cross-
point MIX level in dB.
This is an Extended
Protocol 3000
command.
COMMAND
#X-MIX-LVL  OUT . . . .
ndex> , IN . . . . ,
dB
FEEDBACK
~nn@X-MIX-LVL  OUT . . .
. , IN . . . .
x>,dB
The following attributes comprise
the primary signal ID (suffix 1) and
follower signal ID (suffix 2 or
greater):
▪ – IN
o IN
o OUT
▪ –
o ANALOG_AUDIO
o ANALOG_JACK
o DANTE
▪ < port_index> – The port
number as printed on the front
or rear panel: 1 to 4 for analog
audio, and 1 for Dante
▪ signal_type> – Signal ID
attribute:
o AUDIO
▪ – Indicates a specific
channel number when there
are multiple channels of the
same type: 1 to 4 for Dante,
and 1 for Analog audio
Set analog audio 1 and
Dante 1 cross-point level to -
25dB:
#X-MIX-LVL  OUT.ANALOG
_AUDIO.1.AUDIO.1,IN.D
ANTE.1.AUDIO.1,-
25
X-MIX-
LVL? Get DSP matrix cross-
point MIX level in dB.
This is an Extended
Protocol 3000
command.
COMMAND
#X-MIX-LVL?  OUT . . . . <
index> , IN . . . .
FEEDBACK
~nn@X-MIX-LVL  OUT . . .
. , IN . . . .
x>,dB
The following attributes comprise
the primary signal ID (suffix 1) and
follower signal ID (suffix 2 or
greater):
▪ – IN
o IN
o OUT
▪ –
o ANALOG_AUDIO
o ANALOG_JACK
o DANTE
▪ < port_index> – The port
number as printed on the front
or rear panel: 1 to 4 for analog
audio, and 1 for Dante
▪ signal_type> – Signal ID
attribute:
o AUDIO
▪ – Indicates a specific
channel number when there
are multiple channels of the
same type: 1 to 4 for Dante,
and 1 for Analog audio
Get analog audio 3 and
Dante 2 cross-point level:
#X-MIX-LVL?  OUT.ANALO
G_AUDIO.3.AUDIO.1,IN.
DANTE.1.AUDIO.2
X-MIX-
MUTE Set Matrix cross-point
mute syntax.
This is an Extended
Protocol 3000
command.
COMMAND
#X-MIX-MUTE  OUT . . . . <
index> , IN . . . .
,dB
FEEDBACK
~nn@X-MIX-MUTE  OUT . . .
> . , IN . . . .
ex>,
The following attributes comprise
the signal ID:
▪ –
Direction of the port:
o IN – Input
o OUT – Output
▪ – Type of
signal on the port:
o ANALOG_AUDIO
o DANTE
▪ port_index> – The port
number as printed on the front
or rear panel: 1 to 4 for analog
audio, and 1 for Dante
▪ signal_type> – Signal ID
attribute:
o AUDIO
▪ – Indicates a specific
channel number when there
are multiple channels of the
same type: 1 to 4 for Dante,
and 1 for Analog audio
–
o ON=1
o OFF=0
Set mute status of analog
audio output 1 and Dante
audio cross-point 3 to on:
#X-MIX-MUTE

OUT.ANALOG_AUDIO.1.AU
DIO.1,IN.DANTE.1.AUDI
O.3,1