Kramer 4x4 Audio and Dante Mixer - Manual (Page 43)

Kramer Electronics Ltd.
FC-404NETxl – Protocol 3000 41
Function Description Syntax Parameters/Attributes Example
X-AUD-LVL Set audio level of a
specific signal.
This is an Extended
Protocol 3000
command.
COMMAND
#X-AUD-LVL  . . .
gnal_type> . , audio_level
FEEDBACK
~nn@X-AUD-LVL  . . .
. , audio_level
The following attributes comprise
the signal ID:
▪ –
o IN
o OUT
▪ –
o ANALOG_AUDIO
o ANALOG_JACK
o DANTE
▪ port_index> – The port
number as printed on the front
or rear panel: 1 to 4 for analog
audio, and 1 for Dante
▪ signal_type> – Signal ID
attribute:
o AUDIO
▪ – Indicates a specific
channel number when there
are multiple channels of the
same type: 1 to 4 for Dante,
and 1 for Analog audio
audio_level – Audio level in dB
(range between -100 to +15)
depending of the ability of the
product
Set the audio level of analog
audio specific signal to 10:
#X-AUD-LVL  IN . ANALOG_
AUDIO . 4 . AUDIO . 1 , 10
>
X-AUD-
LVL? Get audio level of a
specific signal.
This is an Extended
Protocol 3000
command.
COMMAND
#X-AUD-LVL?  . . .
.
FEEDBACK
~nn@X-AUD-LVL  . .
. . , audio_level
The following attributes comprise
the signal ID:
▪ –
o IN
o OUT
▪ –
o ANALOG_AUDIO
o ANALOG_JACK
o DANTE
▪ port_index> – The port
number as printed on the front
or rear panel: 1 to 4 for analog
audio, and 1 for Dante
▪ signal_type> – Signal ID
attribute:
o AUDIO
▪ – Indicates a specific
channel number when there
are multiple channels of the
same type: 1 to 4 for Dante,
and 1 for Analog audio
audio_level – Audio level in dB
(range between --100 to +15)
depending of the ability of the
product
Get the audio level of a
specific signal:
#X-AUD-LVL?  out . analo
g_audio . 1 . audio . 1
X-AUD-
MODE Set line/Mic mode.
This is an Extended
Protocol 3000
command.
COMMAND
#X-AUD-MODE  . . .
ignal_type> . , mode
FEEDBACK
~nn@X-AUD-MODE  . .
. . , mode
The following attributes comprise
the signal ID:
▪ –
o IN
▪ –
o ANALOG_AUDIO
▪ – The port
number as printed on the front
or rear panel 1 to 4.
▪ –
o AUDIO
▪ – Indicates a specific
channel number when there
are multiple channels of the
same type 1 to 2.
mode –
1 – Line
2 – Mic
Set AUDIO IN 2 to Mic
mode:
#X-AUD-MODE  IN . ANALOG
_AUDIO . 2 . AUDIO . 1 , 2
>
X-AUD-
MODE? Get line/Mic mode.
This is an Extended
Protocol 3000
command.
COMMAND
#X-AUD-MODE?  . . . <
signal_type> .
FEEDBACK
~nn@X-AUD-MODE  . .
. . , mode
The following attributes comprise
the signal ID:
▪ –
o IN
▪ –
o ANALOG_AUDIO
▪ – The port
number as printed on the front
or rear panel 1 to 4.
▪ –
o AUDIO
▪ – Indicates a specific
channel number when there
are multiple channels of the
same type 1 to 2.
mode –
1 – Line
2 – Mic
Get AUDIO IN 1 to audio
mode:
#X-AUD-MODE?  IN . ANALO
G_AUDIO . 5 . AUDIO . 1