Panasonic AV-HS6000 2 M/E Live Switcher Main Frame & Control Panel (Dual Redundant Power Supplies) - Manual (Page 154)

– 154 –
Chapter 8 System Menu — Setting the external connection
Setting the GPI input/output
Set the GPI input/output port of the Main Frame AV-HS60U1/AV-HS60U2, Control Panel AV-HS60C1/AV-HS60C2/AV-HS60C4.
Setting the GPI input port
Functions can be assigned and externally controlled through the GPI input ports.
f The GPI input ports are the pins 1 to 18 of the terminal on the Main Frame AV-HS60U1/AV-HS60U2, and the pins 1 to 8 of the
terminal on the Control Panel AV-HS60C1/AV-HS60C2/AV-HS60C4. (page 169)
1
Select the button → [PERIPHERAL] → [GPI IN] tab.
2
Select [ID] and select an item.
f Select [Mainframe], [MainPanel], [SubPanel1], or [SubPanel2] as the setting target.
3
Select the port where you want to assign a function from the port list in the left column.
f Select [Select] to filter the port list in the left column. You can select [All], [GPI In1‑6], [GPI In7‑12], or [GPI In13‑18].
4
Select the function to assign from the function list in the right column.
f The input signal type can be selected from the right column function list by selecting [Type]. Type is limited by the function.
- [LowEdge]: Falling edge
- [HighEdge]: Rising edge
- [LowLevel]: Low level
- [HighLevel]: High level
f Select [Group Select] to switch the group of the function list in the right column.
For details, refer to “GPI input function list” (page 154).
5
Select [Assign].
f The function is assigned to the button selected in the step 2 .
f Select [Test Fire] to test the signal input operation of the set GPI port.
r GPI input function list
[Group Select] Signal name Description [Type]
[ME1], [ME2]
KEY1 ON to KEY4 ON
Executes the transition for KEY1 to
KEY4.
[LowEdge] or [HighEdge] KEY1 CUT to KEY4 CUT
Executes the cut transition for KEY1 to
KEY4.
AUTO Executes the auto transition.
CUT Executes the cut transition.
[DSK]
KEY1 ON to KEY4 ON
Executes the cut transition for DSK1 to
DSK4.
[LowEdge] or [HighEdge]
KEY1 CUT to KEY4 CUT
Executes the cut transition for DSK1 to
DSK4.
[USK] USK1 ON - USK4 ON On/off of USK1 ON to USK4 ON. [Low Edge] or [High Edge]
[OTHER]
No Assign No function assigned ―
REC Still1 to REC Still4 Still recording
[LowEdge] or [HighEdge]
REC Clip1 to REC Clip4 Clip recording start
PLAY Clip1 to PLAY Clip4 Clip playback start
STOP Clip1 to STOP Clip4 Clip recording stop or playback stop
FTB FTB transition start
Tally G1 DSBL [Tally Group1] tally signal is not output
[LowLevel] or [HighLevel]
Tally G2 DSBL [Tally Group2] tally signal is not output
Tally G3 DSBL [Tally Group3] tally signal is not output
Tally G4 DSBL [Tally Group4] tally signal is not output
[Macro]
Macro1-1 - Macro9-9
Playback of the applicable macro
register memory (one out of 1-1 to 9-9).
[Low Edge] or [High Edge] Play Cancel Canceling of the macro playback.
Play Resume
Resuming of the paused macro
playback.
@ @ NOTE
t When a plug-in software application is introduced, there are cases where functions inherent to that application are added as functions to be assigned.
Setting the GPI output port
GPI output functions and tally outputs can be assigned and externally output through the GPI output port.
f The GPI output ports are the pins 1 to 48 of the / terminal on the Main Frame AV-HS60U1/AV-HS60U2, and the pins 1 to 10
of the terminal on the Control Panel AV-HS60C1/AV-HS60C2/AV-HS60C4. (page 169)
1
Select the button → [PERIPHERAL] → [GPI OUT] tab.