Setting the main frame av‑hs60u1/av‑hs60u2, Setting the me output and dsk output – Panasonic AV-HS6000 2 M/E Live Switcher Main Frame & Control Panel (Dual Redundant Power Supplies) User Manual
Page 148
– 148 –
Chapter 8 System Menu — Setting the Main Frame AV‑HS60U1/AV‑HS60U2
Setting the Main Frame AV‑HS60U1/AV‑HS60U2
Setting the ME output and DSK output
Video signals can be output in the ME1/ME2/DSK block as shown in the following figure. Each output can be assigned to the SDI OUT signal from the
→
[SDI OUT]
→
[Assign] tab.
ME1
DSK
[Assign]
ME1PGM
ME1PVW
ME1CLN
ME1KEYPVW
ME2PGM
ME2PVW
DSKPGM1
DSKPVW1
DSKPGM2
DSKPVW2 (/DSK1PVW -
DSK4PVW, DSKPST)
ME2CLN
ME2KEYPVW
DSK1CLN (/DSK1PVW)
DSK2CLN (/DSK2PVW)
DSK3CLN (/DSK3PVW)
DSK4CLN (/DSK4PVW)
SEL KEYPVW
XPT
BKGD
KEY1
KEY2
KEY3
KEY4
XPT
BKGD
KEY1
KEY2
KEY3
KEY4
ME2
DSK1
DSK2
DSK3
DSK4
DSK1
DSK2
DSK3
DSK4
Setting the ME1CLN/ME2CLN output
Clean signals (before key effects were added) can be output. Key Out signals using key combinations can also be output.
1
Select the
→
[MAIN FRAME]
→
[ME1,2] tab.
2
Select an item in [Key Select] in the [ME1 CLN]/[ME2 CLN] column.
f
Select the keyer from [Key1] to [Key4].
3
Select an item in [CLN/KOUT] in the [ME1 CLN]/[ME2 CLN] column.
[Clean]
Outputs clean signals before key effects of the keyer set in [Key Select] in the [ME1 CLN]/[ME2 CLN] column were
added.
[Keyout]
Outputs key signals for the keyer set in [Key Select] in the [ME1 CLN]/[ME2 CLN] column.
[Combined KOUT]
Outputs the combined key signal of KEY1 to KEY4.
@
@
NOTE
t
DSK clean signals are output individually from DSK1 to DSK4.
t
DSK Key Out signals cannot be output.
Setting the ME1KEYPVW/ME2KEYPVW output
Preview output exclusive for key. Set whether to output signals with added keyer key effects to the PGM background.
It can be switched with the chroma key adjustment preview screen for the corresponding keyer when [Key1] to [Key4] is selected on the top menu
→
[KEY1] to [KEY4]
→
[Chroma]
→
[Sample]
→
[Chroma PVW].
1
Select the
→
[MAIN FRAME]
→
[ME1,2] tab.
2
Select an item in [Key1 Enable] to [Key4 Enable] in the [ME1 KEYPVW]/[ME2 KEYPVW] column.
[On]
Signals with added key effects of the corresponding keyer is output.
[Off]
No signal is output.
3
Select an item in [Chroma PVW] in the [ME1 KEYPVW]/[ME2 KEYPVW] column.
[Enable]
Displays the preview screen for chroma key adjustment in each preview output.