American Time AllSync Plus - Manual (Page 24)

© American Time
24
AllSync Plus Clock Installation
& Operation Manual
Glossary
Appendix B LED
Illumination
Appendix A
Specifications
Tr
oubleshooting
General Operation
Installation
Intr
oduction
AllSync Plus Clock Specificatios
Page 1 of 2 PS03046 Rev G
140 3rd St. S, PO Box 707, Dassel, MN 55325
800-328-8996 • american-time.com
AllSync Plus ®
Dual Motor
Metal Case
FEATURES
• 5 Year Warranty
• UL/cUL Listed - 12" and 15" surface mount only
• Microprocessor controlled movement
• 15 minutes of backup power (no batteries required)
• Accuracy to within ±1 second of a master clock
• Reduced power consumption
• Attractive modern design
• Heavy-duty construction
• All metal case
• Diagnostic LED
DESCRIPTION
The american time ™ AllSync Plus clocks are provided in round or square metal cases with glass crystals and bold, black
numerals and minute markers on a non-yellowing white dial. Stylish hour and minute hands are aluminum with a black finish
and a red sweep second hand.
The american time ™ AllSync Plus clock is designed to work with multiple master clocks and correction signals. This unit is
programmed to identify the signal it receives from the master and operate as that style of clock. Changing clock operation
from one style to another is as easy as unplugging the clock from one system and plugging it into another. If needed,
changing the placement of 2 small jumpers on the circuit board can change the voltage required to run this clock from
120vac to 24vac or 24vac to 120vac. This clock provides 15 minutes of backup run power without the use of batteries. If a
power outage should last longer than 15 minutes, the clock will synchronize to the master clock at the hourly and 12 hour
correction cycles.
Correction Signals
Works on:
• Hourly Correction: 28.75-35 seconds starting at the 59th minute and 30th second. 12 hour correction: 13 minutes and 52
seconds-18 minutes and 8 seconds starting at 5:12:00 (am and pm). Note: This protocol switches off the run line during
the hourly correction.
ORDERING INFORMATION
Part # Description
U45BHGA404 10" Rd Surface 120vac
U45BHGA?04 10" Rd Flush 120vac
U54BHGA404 12" Rd Surface 120vac
U55BHGA?04 12" Rd Flush 120vac
U57BHGA404 12" Sq Surface 120vac
U58BHGA?04 12" Sq Flush 120vac
U64BHGA404 15" Rd Surface 120vac
U65BHGA?04 15" Rd Flush 120vac
U53BHGA204 12" Rd Double dial wall 120vac
U52BHGA204 12" Rd Double dial ceiling 120vac
U51BHGA204 12" Sq Double dial wall 120vac
U50BHGA204 12" Sq Double dial ceiling 120vac
U63BHGA204 15" Rd Double dial wall 120vac
U62BHGA204 15" Rd Double dial ceiling 120vac
Note:
Replace the ? in the part number with the number from the list below that will correspond with the system you’re replacing.
New flush mount installations require backboxes.
0 = Faraday 1 = National 5 = Simplex ® 6 = Cincinnati/Edwards
7 = 2-hook 8 = Setco 9 = R&H (keyhole)
Also available in Steel Gray. Replace the BH in part number with GH - i.e. U54BHGA404 to U54GHGA404
Part # Description
U45BHHA404 10" Rd Surface 24vac
U45BHHA?04 10" Rd Flush 24vac
U54BHHA404 12" Rd Surface 24vac
U55BHHA?04 12" Rd Flush 24vac
U57BHHA404 12" Sq Surface 24vac
U58BHHA?04 12" Sq Flush 24vac
U64BHHA404 15" Rd Surface 24vac
U65BHHA?04 15" Rd Flush 24vac
U53BHHA204 12" Rd Double dial wall 24vac
U52BHHA204 12" Rd Double dial ceiling 24vac
U51BHHA204 12" Sq Double dial wall 24vac
U50BHHA204 12" Sq Double dial ceiling 24vac
U63BHHA204 15" Rd Double dial wall 24vac
U62BHHA204 15" Rd Double dial ceiling 24vac
®