Panasonic SC-AK15 - Manual (Page 27)

ÍJsíng thé play timer
• Make sure that you have completed "Setting the time" on page 9.
«Switch on the power.
The figure shows how to set the play timer to play a CD from 6:30
a.m. to 7:40 a.m.
I: Press CLOCK/TIMER to select “©PLAY”.
Every time you press the button;
CLOCKS ©PLAY^ ©REC
^Previous display
@ (Within 10 seconds or so)
Press V or A to set the start time display flashing.
'ON" time setting
(T) Press V or A when the start time display is
flashing to set the start time.
(D Press CLOCK/THWER.
Finish time flashes.
'OFF" rime setting
( t ) Press V or A to set the finish time.
® Press CLOCK/TiWlER.
Display returns to original mode.
Source selecrion
Select the desired source and then prepare for
playing.
To play CD(s)
Press CD and insert CD(s).
If more than 1 CD is loaded
Press DISC 1 - DISC 5 to select the CD you want to hear first,
and press a.
Disc selection does not become part of the timer memory.
To play tape(s)
Press TAPE DECK 1/2 and insert tape(s).
If tapes are loaded in both decks, playback will start from
Deck 2.
To play the radio
Press TUNER BAND and tune in the desired station.
To play a unit connected to the “AUX” terminals
Press AUX.
Play volume setting
Set the playback volume.
Press ©PLAY/0REC to select “©PLAY”.
Every time you press the button:
©PLAY----> ©REC
t_(OFF}^--- 1
Power will shut OFF automatically in a few seconds.
The timer play will start at the preset time with volume
increasing gradually up to the volume level you preset.
To switch the timer OFF
Press ©PLAY/0REC and check “©PLAY” goes out.
If you set the timer wrongly
Press ©PLAY/OREC SO that “©PLAY" goes out. Then, repeat the
procedure from step IB .
To check settings
Press CLOCK/TiMER to select “©PLAY".
Two seconds later, the display will change in the following order.
(Î) Play start time
(D Play over time
(?) Piay source and playback volume
You can check settings even when the system is OFF.
To enjoy the desired source after the timer setting is
completed
The volume level and music source are stored in the timer memory
and the timer will start in these preset conditions. However, the Disc
number, reverse mode and tape direction do not get stored in the
timer memory.
1. After step El, turn on the power and start playing the desired
source.
2 . (After playing the desired source)
When you select CD as the timer source
Confirm that the CD(s) is(are) loaded.
• if more than 1 CD is loaded
Reset the Disc number if it has been changed, and press h .
When you select tape as the timer source
Confirm that the tape(s) is(are) loaded,
Reset the reverse mode and tape direction if you have changed
any of them, (if tapes are loaded in both decks, check Deck 2
tape direction.)
Press POWER to put the unit on standby.
Turning the timer ON/OFF
As long as “©PLAY” is displayed, the play timer will come ON
everyday as set.
You can turn the timer ON/OFF by pressing ©PLAY/0REC while
power is OFF.
Remember that when “©PLAY” is displayed, the timer is ON. When
not displayed, the timer is OFF.
• If the power is on, the timer wii! not function. The system must be
in the standby mode.
• If you switch the power to the standby mode while the play timer
is functioning, the OFF time setting will not be activated.
• If AUX is selected as the source, when the timer comes ON, the
system will turn ON and will engage “AUX" as the source. If you
want playback from the connected component to start, set the
component's timer to the same time. (See the instruction manual
that came with the component.)
V)
.S
0»
&
S