Panasonic PV-7664 - Manual (Page 35)

VCR Plus+ Programming
'oble Box
onlrol Easy Taping.
[^1
Before you begin, make sure...
□ The clock is set.
□ VCR Plus+ Setup is complete
(see page 34).
^ 6 il. ...
1 Ij
i OO // s»l\W
■-- -
Multi Function Display
vcft TV CATV
■©03
o © ©
" © ® ©
© © ©
SPEED
ADD/
DELETE
Use normal Timer Recording steps if:
• the PlusCode for a program is not listed.
• you anticipate the program, such as a sporting
event, to run over the scheduled stop time.
See page 23 to:
• cancel a timer recording in progress.
• replace program contents.
• review or clear program contents once set.
Important notes when using a DSS receiver
• When recording programs via a DSS receiver,
the DSS receiver must be left on.
• When recording programs via an antenna or
cable, the DSS receiver must be turned off.
Push PROG to
display the “SET
PROGRAM” screen.
............ SET PROGRAM .................
VCR Plus+ PROGRAM
TIMER PROGRAM
Push AT to select
“VCR P1US+
PROGRAM,” and then
push ► to display the
“VCR Plus+" screen.
VCR PI 0 S+
ENTER PLUSCODE NUMBER
/1 \
USING 0-9 KEYS
END :PROG KEY
Push the NUMBERED keys to
enter the PlusCode number.
• Refer to your local TV listings.
To Make Corrections
Push 4 repeatedly to delete the PlusCode
number. Then, enter the correct number.
VCR Plus*
ENTER PLUSCODE NUMBER
123456
US NG 0-9 KEYS
BACKSPACE KEY
ENTER :PROG KEY
O
Push PROG to lock in
your program.
Push the 1, 2 or 3 key to
select the program type.
To change the recording speed:
Push SPEED for SP, LP or SLP.
To cancel program contents:
Push ADD/DLT.
VCR PIUS+
1 ONE TIME
2 DAILY(MON-FRI)
3 WEEKLY
TO SELECT PUSH 1.2 OR 3
DATE START STOP
TO CHANGE RECORD SPEED
PUSH SPEED KEY
CANCEL:ADD/OLT KEY
ACCEPT:PROG KEY
If you use connection type 1 on page 12, the channel shown in this on-___
screen display will always be the cable box output channel number.
Push PROG
if contents are
acceptable.
If programs are overlapped,
a warning screen will appear.
P DT START STOP CH SPD
1DAY 9:OOA12:OOA 06 SP
3 ----------;-----------
4 ------------------------ ;----- ------ ------------
CANCEL:ADD/DLT KEY
SELECT 1
-8:i ▼ KEY
ENTER :► KEY
END :PROG KEY
Push PROG to
complete the
program.
When recording programs via a cable box,
make sure the cable box is left on. If the cable
box can not be controlled with the VCR, you
must manually select the desired channel.
TURN VCR OFF
FOR TIMER RECORDING
AND
LEAVE CABLE BOX POWER ON
This display may differ depending
on your cable box hook-up.
POWER
Push POWER off
to set the timer.
-iEsiia-
Multi Function Display
For a list of publications that carry the PlusCode numbers in your area, call 1 - 800 - 258 - 4827.
You can obtain unlisted PlusCode numbers by catling 1 - 900 - 454 - 7587. Cali costs approximately $.95 per minute.
VCR PlusCodes can not be used to program the VCR to record DSS channels.
Avoid overlapping program times. (TTie overlapping programs wilt flash on the screen.)
An on-screen display will indicate if an invalid PlusCode number has been entered or when all timer programs are full.
35