For eegor, And ultra eegor, Benders only – Gardner Bender Guide to Profitable Bending User Manual
Page 7: Forming a saddle bend, 4" conduit offset chart 3, Conduit offset chart
50
Forming a Saddle Bend
1. Repeat steps listed in Operating Procedures and complete the first
offset bend.
2. Do not remove conduit. Keep all adjustments and settings the same.
Raise the bender handle until the conduit can be slid forward. Slide
the conduit forward until the end of the first offset bend is positioned
past the second jaw. See Figure 6. Level the conduit and hold it
steady.
Figure 6
3. Push the handle down to complete the second offset bend. See
Figure 7. Raise the handle and remove the conduit.
Figure 7
7
For Eegor
™
and Ultra Eegor
™
Benders Only
4" Conduit Offset Chart
3
1
⁄
2
" Conduit Offset Chart
Desired
Measurement (B) (inches)
Offset
(H)
15°
30°
45°
60°
2"
7
9
⁄
16
—
—
—
4"
15
5
⁄
16
—
—
—
6"
23
—
—
—
8"
30
3
⁄
4
15
1
⁄
2
—
—
10"
38
1
⁄
2
19
1
⁄
2
—
—
12"
46
3
⁄
16
23
1
⁄
2
—
—
14"
53
15
⁄
16
27
1
⁄
2
18
5
⁄
8
—
16"
61
11
⁄
16
31
1
⁄
2
21
1
⁄
2
—
18"
69
3
⁄
8
35
1
⁄
2
24
5
⁄
16
—
20"
77
1
⁄
8
39
1
⁄
2
27
1
⁄
8
—
22"
84
7
⁄
8
43
1
⁄
2
29
15
⁄
16
—
24"
92
9
⁄
16
47
1
⁄
2
32
13
⁄
16
25
1
⁄
4
26"
100
5
⁄
16
51
1
⁄
2
35
5
⁄
8
27
9
⁄
16
28"
108
55
1
⁄
2
38
7
⁄
16
29
7
⁄
8
30"
115
3
⁄
4
59
1
⁄
2
41
1
⁄
4
32
3
⁄
16
Desired
Measurement (B) (inches)
Offset
(H)
15°
30°
45°
60°
4"
15
5
⁄
16
—
—
—
6"
23
—
—
—
8"
30
3
⁄
4
—
—
—
10"
38
7
⁄
16
19
7
⁄
16
—
—
12"
46
3
⁄
16
23
7
⁄
16
—
—
14"
53
15
⁄
16
27
7
⁄
16
—
—
16"
61
5
⁄
8
31
7
⁄
16
21
5
⁄
16
—
18"
69
3
⁄
8
35
7
⁄
16
24
1
⁄
8
—
20"
77
1
⁄
8
39
7
⁄
16
27
—
22"
84
13
⁄
16
43
7
⁄
16
29
13
⁄
16
—
24"
92
9
⁄
16
47
7
⁄
16
32
5
⁄
8
24
15
⁄
16
26"
100
5
⁄
16
51
7
⁄
16
35
7
⁄
16
27
1
⁄
4
28"
108
55
7
⁄
16
38
5
⁄
16
29
9
⁄
16
30"
115
3
⁄
4
59
7
⁄
16
41
1
⁄
8
31
7
⁄
8
See page 11 for Eegor™ bending shoe radii table.
E-507 Guide to Profitable Bending rA.qxd 10/19/09 3:17 PM Page 13