For eegor, And ultra eegor, Benders only – Gardner Bender Guide to Profitable Bending User Manual
Page 6: Conduit reamer, Repeat bending feature, Conduit offset chart 3" conduit offset chart
51
Conduit Reamer
1. The conduit reaming tool has a blade for the inside and outside sur-
face of the conduit. Complies with article 348-11 of NEC.
2. Press the open end of the conduit against the reamer blade. Hold
the conduit firmly and rotate it 2 or 3 times to remove burrs and
sharp edges. See Figure 8.
Repeat Bending Feature
1. An adjustable length indicator is located on the front edge of the
bend frame. The indicator has a maximum travel of 4 inches. See
Figure 9.
2. Position the conduit into the bending jaws. Loosen the thumb screw
and move the indicator until it contacts the end of the conduit.
Tighten the thumb screw. See Figure 9.
Figure 8
Figure 9
Adjustable
Length
Indicator
For Eegor
™
and Ultra Eegor
™
Benders Only
2" & 2
1
⁄
2
" Conduit Offset Chart
3" Conduit Offset Chart
Desired
Measurement (B) (inches)
Offset
(H)
15°
30°
45°
60°
2"
7
5
⁄
8
—
—
—
4"
15
3
⁄
8
—
—
—
6"
23
1
⁄
16
11
11
⁄
16
—
—
8"
30
13
⁄
16
15
11
⁄
16
—
—
10"
38
1
⁄
2
19
11
⁄
16
13
7
⁄
16
—
12"
46
1
⁄
4
23
11
⁄
16
16
1
⁄
4
—
14"
54
27
11
⁄
16
19
1
⁄
16
14
5
⁄
8
16"
61
11
⁄
16
31
11
⁄
16
21
7
⁄
8
16
15
⁄
16
18"
69
7
⁄
16
35
11
⁄
16
24
3
⁄
4
19
1
⁄
4
20"
77
3
⁄
16
39
11
⁄
16
27
9
⁄
16
21
9
⁄
16
22"
84
7
⁄
8
43
11
⁄
16
30
3
⁄
8
23
7
⁄
8
24"
92
5
⁄
8
47
11
⁄
16
33
3
⁄
16
26
3
⁄
16
26"
100
3
⁄
8
51
11
⁄
16
36
1
⁄
16
28
1
⁄
2
28"
108
1
⁄
16
55
11
⁄
16
38
7
⁄
8
30
13
⁄
16
30"
115
13
⁄
16
59
11
⁄
16
41
11
⁄
16
33
1
⁄
8
6
Desired
Measurement (B) (inches)
Offset
(H)
15°
30°
45°
60°
2"
7
5
⁄
8
—
—
—
4"
15
5
⁄
16
—
—
—
6"
23
1
⁄
16
11
5
⁄
8
—
—
8"
30
3
⁄
4
15
5
⁄
8
—
—
10"
38
1
⁄
2
19
5
⁄
8
13
1
⁄
4
—
12"
46
1
⁄
4
23
5
⁄
8
16
1
⁄
16
—
14"
53
15
⁄
16
27
5
⁄
8
18
7
⁄
8
—
16"
61
11
⁄
16
31
5
⁄
8
21
3
⁄
4
16
5
⁄
8
18"
69
7
⁄
16
35
5
⁄
8
24
9
⁄
16
18
15
⁄
16
20"
77
1
⁄
8
39
5
⁄
8
27
3
⁄
8
21
1
⁄
4
22"
84
7
⁄
8
43
5
⁄
8
30
3
⁄
16
23
1
⁄
2
24"
92
5
⁄
8
47
5
⁄
8
33
1
⁄
16
25
13
⁄
16
26"
100
5
⁄
16
51
5
⁄
8
35
7
⁄
8
28
1
⁄
8
28"
108
1
⁄
16
55
5
⁄
8
38
11
⁄
16
30
7
⁄
16
30"
115
3
⁄
4
59
5
⁄
8
41
1
⁄
2
32
3
⁄
4
E-507 Guide to Profitable Bending rA.qxd 10/19/09 3:17 PM Page 11