Neff S72T69X3GB Instruction Manuals and User Guides
We have 2 Instruction Manuals and User Guides for S72T69X3GB Neff
Manuals 
| Recognized languages: | English |
|---|---|
| Pages: | 40 |
| Size: | 2.26 MB |
Show table of contents
Document Outline
- 8 Intended use
- Intended use
- ( Safety instructions
- Delivery
- 1. Check the packaging and dishwasher immediately for damage caused in transit. Do not switch on a damaged appliance, but contact your supplier.
- 2. Please dispose of the packaging material in an environmentally friendly manner.
- 3. Do not let children play with packaging and its parts. There is a risk of suffocation from collapsible boxes and film.
- Installation
- In daily use
- Childproof lock (door lock)Door lock *
- Damage
- Disposal
- ■ To prevent injuries, e.g. caused by stumbling, open the dishwasher only briefly in order to load and unload the dishwasher.
- ■ Knives and other utensils with sharp points must be placed horizontally in the cutlery drawer.
- ■ Do not lean or sit on the open door.
- ■ In the case of free-standing appliances, ensure that the baskets are not overloaded.
- ■ If the appliance is not in a cavity and a side panel is accessible, the door hinge area must be covered at the side for reasons of safety (risk of injury). The covers are available as optional accessories from customer service or specialist outlets.
- ■ If fitted, use the childproof lock. An exact description can be found in the back of the enve lope.
- ■ Do not allow children to play with or operate the appliance.
- ■ Keep children away from detergents and rinse aid. These may cause chemical burns in the mouth, throat and eyes or asphyxiation.
- ■ Keep children away from open dishwasher. The water in the rinsing compartment is not drinking water and could contain detergent residue.
- ■ Ensure that children do not place fingers in the tablet collecting tray 1B. Small fingers could become caught in the slots.
- ■ When opening and closing the door on an eye-level appliance, ensure that children do not become jammed or crushed between the appliance door and the cupboard door below.
- ■ Children could become locked in the appliance (danger of suffocation) or get into another dangerous situation.
- 7 Protection of the environment
- * Getting to know your appliance
- + Water softening system/Special salt
- Water softening system/Special salt
- Setting
- 1. Find out about the hardness value of your tap water. Your water utility company will help you with this.
- 2. Set value can be found in the water hardness table.
- 3. Open the door.
- 4. Switch on ON/OFF switch (.
- 5. Hold down programme button # and press START button )" until •:‹.... is indicated on the digital display.
- 6. Release both buttons.
- To change the setting:
- Water hardness table
- Using special salt
- Using detergents with salt componentDetergents with salt component
- Switching off salt refill indicator/water softening systemSwitching off water softening system
- , Rinse aid
- Rinse aid
- Setting amount of rinse aid
- Switching off rinse aid refill indicator
- - Utensils
- Utensils
- Not suitable
- Glass and utensil damage
- Loading the dishwasher
- Unloading the dishwasher
- Cups and glasses
- Pans
- Cutlery drawer
- Folding spikesFolding spikes *
- Small accessories holder *Small accessories holder
- Adjusting the height of the basket
- Appliance height 81.5 cm
- 16 cm
- 30 cm
- 18.5 cm
- 27.5 cm
- 21 cm
- 25 cm
- 18 cm
- 33 cm
- 20.5 cm
- 30.5 cm
- 23 cm
- 28 cm
- 1. Pull out the top basket 12 out.
- 2. To lower the basket, press in the left and then the right lever on the outside of the basket. In doing so, hold the sides of the basket along the upper edge to prevent it from suddenly dropping.
- 3. To raise the basket, hold the basket on the sides of the upper edge and lift it up.
- 4. Before re-inserting the basket again, ensure that it is at the same height on both sides. Otherwise, the appliance door cannot be closed and the upper spray arm will not be connected to the water circuit.
- . Detergent
- / Overview of programmes
- Overview of programmes
- The max. possible number of programmes is illustrated in this overview. The corresponding programmes and their arrangement can be found on the fascia.
- Programme selection
- Information for test institutes
- 0 Additional options
- 1 Operating the appliance
- Operating the appliance
- Programme data
- Aqua sensorAqua sensor *
- Switching on the appliance
- Optical display while the programme is runningOptical display while the programme is running *
- Remaining running time display
- Timer programming
- 1. Open the door.
- 2. Switch on ON/OFF switch (.
- 3. Press the button ` + until ‹‚ is flaching in the timer programming display X.
- 4. Press + or – button until the ` displayed time corresponds with your requirements.
- 5. Press START button )", timer programming is activated.
- 6. To delete timer programming `, press the + or – button until ‹‹ is indicated on the digital display X.
- 7. Close the door.
- End of programme
- Automatic switch off after end of programme or interior light*Automatic switch off / interior light
- Switching off the appliance
- Interrupting the programme
- Terminating the programmeTerminating the programme (Reset)
- Changing the programme
- Intensive drying
- 2 Cleaning and maintenance
- Cleaning and maintenance
- Overall condition of the machine
- Special salt and rinse aid
- Filters
- 1. After each washing cycle check the filters for residue.
- 2. Unscrew filter cylinder as illustrated and take out filter system.
- 3. Remove any residue and clean filters under running water.
- 4. Re-install filter system in reverse sequence and ensure that the arrow marks are opposite each other after closing the filter system.
- Spray arms
- 3 Fault, what to do?
- Fault, what to do?
- Note
- Waste water pump
- m Warning
- Risk of cuts!
- 1. First always disconnect the appliance from the power supply.
- 2. Take out top basket 12 and bottom basket 1b.
- 3. Remove the filters 1Z.
- 4. Scoop out water, use a sponge if required.
- 5. Prise out the white pump cover (as illustrated) using a spoon. Grip the cover on the crosspiece and lift diagonally inwards. Remove cover completely.
- 6. Check impeller wheel and remove any foreign objects.
- 7. Place cover in the original position and press down until it engages (click).
- 8. Install filters.
- 9. Re-insert baskets.
- Risk of cuts!
- Fault table
- m Warning
- 4 Customer service
- 5 Installation and connection
- Installation and connection
- Product package
- Safety instructions
- Delivery
- Technical specifications
- Installation
- Waste-water connection
- Drinking water connection
- Warm water connection *Warm water connection
- Electrical connection
- Removing the appliance
- Transportation
- Drain the appliance according to the following steps:
- 1. Turn on the tap.
- 2. Open the door.
- 3. Switch on ON/OFF switch (.
- 4. Select programme with the highest temperature.
- 5. Press START button )".
- 6. Close the door.
- 7. Open door after approx. 4 minutes.
- 8. Press START button )" until ‹:‹‚ is indicated on the digital display.
- 9. Close the door.
- 10. Open door after approx. 1 minute.
- 11. Switch off ON/OFF switch (.
- 12. Turn off the tap, disconnect supply hose and drain water.
- Drain the appliance according to the following steps:
- Protection against frostProtection against frost (Emptying the appliance)
| Recognized languages: | English |
|---|---|
| Pages: | 30 |
| Size: | 2.13 MB |
Show table of contents
Document Outline
- en Table of contents
- Safety instructions 4
- Getting to know your appliance 6
- Water softening system 7
- Special salt $ 8
- Rinse aid % 9
- Utensils 10
- Detergent 13
- Overview of programmes 15
- Additional options 16
- Washing the dishes 16
- Maintenance and care 19
- Troubleshooting 21
- Customer service 24
- Installation 24
- Waste disposal 27
- Safety instructions
- Please read the operating and installation instructions carefully. They contain important information on how to install, use and maintain the appliance.
- Retain all documents for subsequent use or for the next owner.
- Read the “Installation” chapter to learn how to install and connect the appliance correctly.
- m Warning
- Knives and other utensils with sharp points must be placed horizontally in the cutlery drawer.
- The description of the childproof lock is at the back in the envelope.
- * depending on model
- m Warning
- Children could become locked in the appliance (risk of suffocation) or find themselves in other dangerous situations.
- Therefore: Pull out the mains plug, sever and dispose of the power cord. Destroy the door lock so that the door can no longer be closed.
- Diagrams of the control panel and the interior of the appliance can be found in the envelope at the front.
- Individual positions are referred to in the text.
- (
- ON/OFF switch
- 0
- Programme buttons **
- 8
- Digital display
- @
- Display “Check water supply”
- H
- Salt refill indicator
- P
- Rinse aid refill indicator
- X
- Timer programming display
- `
- Timer programming
- h
- Additional options **
- )"
- START button
- )*
- Door opener
- ** Number depending on model
- 1"
- Interior light *
- 1*
- Cutlery drawer
- 12
- Top basket
- 1:
- Top spray arm
- 1B
- Tablet collecting tray
- 1J
- Bottom spray arm
- 1R
- Dispenser for special salt
- 1Z
- Filters
- 1b
- Bottom basket
- 1j
- Dispenser for rinse aid
- 9"
- Detergent dispenser
- 9*
- Lock for detergent dispenser
- 92
- Rating plate
- * depending on model
- The settings can be found in the individual chapters.
- •
- Water Hardness •:‹‹ - •:‹ˆ
- š
- Intensive drying š:‹‹ - š:‹‚
- §
- Rinse aid §:‹‹ - §:‹‡
- ‘
- Hot water ‘:‹‹ - ‘:‹‚
- ›
- End of programme buzzing sound ›:‹‹ - ›:‹„
- ˜
- Automatic disconnection ˜:‹‹ - ˜:‹ƒ
- ‚
- Optical display while the programme is running ‚:‹‹ -‚:‹‚
- To ensure good washing results, the dishwasher requires soft water, i.e. containing low amounts of lime, otherwise white limescale will be deposited on the utensils and inner container.
- Tap water above 9° Clarke must be softened. The water is softened with salt (regeneration salt) in the water softening system of the dishwasher.
- The setting and therefore the required amount of salt depends on the degree of hardness of your tap water (see table).
- The amount of salt dispensed can be set from •:‹‹ to •:‹ˆ.
- Salt is not required at the set value •:‹‹.
- Always refill with special salt immediately before switching on the appliance. This ensures that overrun special salt solution is immediately washed out and does not corrode the rinsing tank.
- As soon as the salt refill indicator H on the fascia is lit, top up the salt.
- * depending on model
- If combined detergents with a salt component are used, salt can usually be omitted up to a water hardness of 21° dH (37° fH, 26° Clarke, 3.7 mmol/l). If the water hardness is over 21° dH, special salt must be used.
- If the salt refill indicator H is impaired (e.g. when using combined detergents containing salt component), it can be switched off.
- m Warning
- Never fill the salt dispenser with detergent. You will destroy the water softening system.
- As soon as the rinse-aid refill indicator P is lit on the fascia, there is still a rinse-aid reserve of 1 – 2 rinsing processes. Refill with rinse aid.
- The rinse aid is required for stain-free utensils and clear glasses. Use only rinse aid for domestic dishwashers.
- Combined detergents with rinse-aid component may be used up to a water hardness of 21° dH (37° fH, 26° Clarke, 3.7 mmol/l) only. If the water hardness is over 21° dH, rinse aid must be used.
- The amount of rinse aid can be set from §:‹‹ to §:‹‡. Please set rinse aid on §:‹† to obtain very good drying results (§:‹† is already set in factory).
- Change this setting, only if streaks (select lower setting) or water stains (select higher setting) are left on the utensils.
- If the rinse-aid refill indicator P is impaired (e.g. when using combined detergents containing rinse aid component), it can be switched off.
- The rinse aid refill indicator P is now switched off.
- Aluminium and silver parts have a tendency to discolour and fade during the wash cycle. Even some types of glass (e.g. crystal glass objects) may turn cloudy after many wash cycles.
- Causes:
- Recommendation:
- Very small utensils should not be washed in the machine, as they may fall out of the baskets.
- To prevent water from dripping off the upper basket onto the utensils in the lower basket, it is recommended to empty the appliance from the bottom up.
- Hot utensils are sensitive to shock! Therefore, when the programme ends, leave the utensils to cool down in the dishwasher until they can be handled.
- Top basket 12
- Bottom basket 1b
- Tip
- Heavily soiled utensils (pans) should be placed in the bottom basket. The more powerful spray jet provides a better dishwashing result.
- Tip
- Other examples, such as the best way of loading your dishwasher, can be found on our homepage as a free download. The corresponding Internet address can be found on the back page of these instructions for use.
- Arrange the cutlery in the cutlery drawer 1* as illustrated. Separately arranged utensils are easier to remove after washing.
- The drawer can be taken out.
- Depending on the model, you can fold down the side shelves to provide more room for taller items of cutlery. The front rows of prongs can be folded down to provide room for wider handles.
- * depending on model
- The spikes can be folded down to improve arrangement of pans, bowls and glasses.
- * depending on model
- Light-weight plastic accessories, e.g. cups, lids, etc. can be held securely in the small accessories holder.
- The height of the upper utensils basket 12 can be adjusted in 3 stages to create more space either in the upper or lower basket.
- Appliance height 81.5 cm
- Top basket
- Bottom basket
- Setting 1 max. ø
- 16 cm
- 30 cm
- Setting 2 max. ø
- 18.5 cm
- 27.5 cm
- Setting 3 max. ø
- 21 cm
- 25 cm
- Appliance height 86.5 cm
- Top basket
- Bottom basket
- Setting 1 max. ø
- 18 cm
- 33 cm
- Setting 2 max. ø
- 20.5 cm
- 30.5 cm
- Setting 3 max. ø
- 23 cm
- 28 cm
- You can use tablets as well as powder or liquid detergents for dishwashers, but never use washing up liquid. The dosage can be individually adjusted with powder or a liquid detergent according to the degree of soiling. Tablets contain an adequately l...
- Note
- To ensure a good washing result, always follow the instructions on the detergent packaging!
- If you have further questions, we recommend that you contact the detergent manufacturers’ helpline.
- m Warning
- Read and observe the safety information and instructions for use on the packaging for cleaning and rinsing agents.
- Tip
- If the utensils are only lightly soiled, slightly less than the indicated amount of detergent is usually adequate.
- Suitable detergents and care products can be purchased online via our website or via customer service (see back page).
- Apart from conventional detergents (Solo), a number of products are offered with additional functions. These products contain not only the detergent but also rinse-aid and salt replacement substances (3in1) and, depending on the combination (4in1, 5i...
- As soon as combined detergents are used, the rinse programme is adjusted automatically to ensure the best possible rinsing and drying result.
- The max. possible number of programmes is illustrated in this overview. The corresponding programmes for your appliance can be found on the fascia.
- Type of utensils
- Type of soiling
- Programme
- Possible additional options
- Programme sequence
- pots and pans, non-sensitive utensils and cutlery
- very adhesive burned-in or dried-on food remnants containing starch or protein
- ¹
- Auto 65° – 75°
- all
- Is optimised according to the soiling with the aid of sensors.
- Á
- Auto 45° – 65°
- mixed utensils and cutlery
- part dried, common household food remnants
- б / а
- Eco 50°
- Prerinse
- Clean 50°
- Intermediate rinse
- Final rinse 65°
- Dry
- sensitive utensils, cutlery, temperature- sensitive plastic and glasses
- slightly adhesive, fresh food remnants
- É
- Auto 35° – 45°
- Intensive zone
- Express Wash/ Speed Perfect (VarioSpeed)
- Half load
- Extra drying
- Is optimised according to the soiling with the aid of sensors.
- с / р
- Quick 45°
- Extra drying
- Clean 45°
- Intermediate rinse
- Final rinse 55°
- all
- cold rinsing, intermediate cleaning
- щ / ш
- Prerinse
- none
- Prerinse
- You can select a suitable programme according to the type of utensils and degree of soiling.
- Test institutes can request the conditions for running comparison tests by sending an e-mail to
- [email protected].
- Quote the appliance number (ENr.) and the production date (FD) which you can find on the rating plate 92 on the appliance door.
- * depending on model
- Additional options can be set with the buttons h.
- This function can reduce the running time by approx. 20% to 50% depending on the selected rinse programme. The change in the running time is indicated on the digital display 8. To obtain optimum cleaning results at a reduced running time, water and e...
- If you have only a few items to wash (e.g. glasses, cups, plates), you can switch to “half load”. This will save water, energy and time. It is recommended to put a little less detergent in the detergent dispenser than for a full load.
- The temperature is increased during the cleaning process. This increases the hygiene status. This additional option is ideal for cleaning e.g. chopping boards and baby bottles.
- Perfect for a mixed load. You can wash very soiled pots and pans in the lower basket together with normally soiled utensils in the upper basket. The spray pressure in the lower basket is intensified, the rinsing temperature is increased slightly.
- An increased temperature during the final rinse and an extended drying phase ensure that even plastic parts dry better. There is a slight increase in the energy consumption.
- The programme data (consumption values) can be found in the summary of instructions. They refer to normal conditions and the water hardness set value •:‹…. Different influencing factors such as e.g. water temperature or line pressure may result...
- * depending on model
- The Aqua sensor is an optical measuring device (light barrier) which measures the turbidity of the rinsing water.
- The Aqua sensor is used according to the programme. If the Aqua sensor is active, “clean” rinsing water can be transferred to the next rinse bath and water consumption can be reduced by 3–6 litres. If the turbidity is greater, the water is drai...
- * depending on model
- While the programme is running, a light spot shines on the floor under the appliance door. Do not open the dishwasher door until the light point is no longer visible on the floor.
- If the appliance is installed at eye-level, with flush furniture front, the light point is not visible.
- This function can be changed as follows:
- When the programme is selected, the remaining running time of the programme is indicated on the digital display 8.
- The running time is determined during the programme by the water temperature, the number of utensils as well as the degree of soiling and may vary (depending on the selected programme).
- You can delay the start of the programme in 1 hour steps up to 24 hours.
- The programme has ended when the value ‹:‹‹ is indicated on the numerical display 8.
- The end of the programme is also indicated by an acoustic signal. This function can be changed as follows:
- * depending on model
- To save energy, the dishwasher can be automatically switched off 1 min or 120 min after the programme ends.
- The setting can be selected from ˜:‹‹ to ˜:‹ƒ.
- ˜:‹‹
- Appliance does not switch off automatically.
- The interior light 1" comes on when the door is opened irrespective of whether the ON/OFF switch ( is switched on or off. When the door is closed the light is off. If the door is open for longer than 60 min., the light switches off automatically. The...
- ˜:‹‚
- Appliance switches off after 1 min.
- ˜:‹ƒ
- Appliance switches off after 120 min.
- Short time after the end of the programme:
- m Warning
- At the end of the programme please open the door fully and not partially when emptying the dishwasher. Any escaping water vapour could damage sensitive worktops.
- When the START button )" has been pressed, the programme cannot be changed.
- The only way a programme can be changed is by Cancel programme (Reset).
- The final rinse uses a higher temperature which improves the drying result. The running time may increase slightly. (Caution if utensils are delicate!)
- A regular inspection and maintenance of your machine will help to prevent faults. This saves time and prevents problems.
- If you find such deposits:
- Clean the appliance with detergents/ appliance cleaners which are particularly suitable for use with dishwashers.
- Never use a steam cleaner to clean your dishwasher. The manufacturer is not liable for any consequential damage.
- Regularly wipe the front of the appliance and fascia with a damp cloth; water and a little washing up liquid are adequate. Do not use sponges with a rough surface or abrasive detergents, as these could scratch the surfaces.
- Stainless steel appliances: To prevent corrosion, avoid using sponge cloths or wash them out thoroughly several times before using for the first time.
- m Warning
- Never use other chlorinated household detergents! Health hazard!
- The filters 1Z keep large foreign objects in the rinsing water away from the pump. These foreign objects may occasionally block the filters.
- The filter system consists of a coarse filter, a flat fine filter and a microfilter.
- Limescale and contaminants in the rinsing water may block nozzles and bearings on the spray arms 1: and 1J.
- The majority of faults which could occur in daily operation can be rectified by the user. This ensures that the appliance is quickly available for use again. The following overview will help you locating the causes and gives helpful advise to elimina...
- Note
- If the appliance stops during dishwashing or does not start for no obvious reason, first run the Abort programme function (Reset).
- (See chapter entitled “Dishwashing”)
- m Warning
- If on the digital display 8 an error code (“:‹‚ to “:„‹), always disconnect the appliance from the power supply and then turn off the tap.
- You can rectify certain faults yourself (see following fault description), for all other faults please contact customer service and state the indicated fault “:XX.
- m Warning
- Don’t forget: Repairs may be carried out by technicians only. If a component has to be replaced, ensure that only original spare parts are used. Improper repairs or use of non-original spare parts may cause considerable damage and put the user at c...
- Large food remnants or foreign objects which were not captured by the filters may block the waste water pump. The rinsing water will then be above the filter.
- In this case:
- If phosphate-free detergents are used with hard tap water, white deposits may be deposited more easily on utensils and the container walls.
- Contact the detergent manufacturer, in particular if:
- If the advice given does not resolve your problem, please contact your customer service. Contact details can be found on the back cover of this instruction manual or in the enclosed customer service list. When calling , please quote the appliance num...
- Rely on the expertise of the manufacturer. Call us to ensure that the repair will be carried out by fully-trained service engineers, who are equipped with original spare parts for your appliance.
- The dishwasher must be connected correctly, otherwise it will not function properly. The specifications for the inlet and outlet as well as the electrical connected loads must correspond with the required criteria as specified in the following paragr...
- Install the appliance in the correct sequence:
- m Warning
- If the appliance is not in a cavity and a side panel is accessible, the door hinge area must be covered at the side for reasons of safety (risk of injury). The covers are available as optional accessories from customer service or specialist outlets.
- Your dishwasher has been checked thoroughly in the factory to ensure that it is in working order. This may cause small water stains. These will disappear after the first wash cycle.
- Weight:
- max. 60 kg
- Voltage:
- 220–240 V, 50 Hz or 60 Hz
- Connected load:
- 2.0–2.4 kW
- Fuse:
- 10/16 A (UK 13A)
- Water pressure:
- at least 0.05 MPa (0.5 bar), maximum 1 MPa (10 bar). At a higher water pressure: connect pressure-reducing valve ahead.
- Inlet rate:
- minimum 10 litres/minute
- Water temperature:
- cold water; hot water max. temperature 60 °C.
- The required installation dimensions can be found in the installation instructions. Level the appliance with the aid of the height-adjustable feet. Ensure that the appliance is situated securely on the floor.
- * depending on model
- The dishwasher can be connected to cold or hot water up to max. 60 °C.
- Connection to hot water is recommended if the hot water can be supplied by energetically favourable means and from a suitable installation, e.g. solar heating system with circulation line.
- This will save energy and time.
- The hot water setting ‘:‹‚ allows you to adjust your appliance optimally to operation with hot water.
- It is recommended to have a water temperature (temperature of the incoming water) of at least 40 °C and no more than 60 °C.
- It is not recommended to connect the appliance to hot water if the water is supplied from an electric boiler.
- Also observe the sequence of worksteps here.
- Empty the dishwasher and secure loose parts.
- Transport appliance upright only.
- (This prevents residual water from running into the machine control and damaging the programme sequence.)
- If the appliance is in a room where there is a risk of frost (e.g. holiday home), empty the appliance completely (see Transportation).
- Both the packaging of new appliances and the old appliances themselves contain valuable raw materials and recyclable materials.
- Please dispose of the individual parts separated according to type.
- Please ask your dealer or inquire at your local authority about current means of disposal.
- All plastic parts of the appliance are identified with internationally standardised abbreviations (e.g. >PS< polystyrene). Therefore, plastic waste can be sorted out when the appliance is being disposed of.
- Please follow the safety instructions under “Delivery”.
- Please follow the safety instructions under “Disposal of your appliance”.
- This appliance is identified according to the European guideline 2002/96/EC on waste electrical and electronic equipment – WEEE. The guideline specifies the framework for an EU-wide valid return and re-use of old appliances.