Carrier D2-3466-2 Instruction Manuals and User Guides
We have 1 Instruction Manual and User Guide for D2-3466-2 Carrier
Manuals 
| Recognized languages: | English |
|---|---|
| Pages: | 38 |
| Size: | 817 KB |
Show table of contents
Document Outline
- Carrier VFD Quick Reference
- Chapter 1 Using This Manual
- Chapter 2 Identifying Drive Components Using Reference Drawings and Parts Lists
- Chapter 3 Using the Keypad/Display to Program, Monitor, and Control the Drive..............3-1
- Chapter 4 Identifying Parameter Defaults For Carrier Drives...............................................4-1
- Chapter 5 Verifying the Installation ...............................................5-1
- Chapter 6 Troubleshooting the Drive
- Chapter 1 Using This Manual
- Chapter 2 Identifying Drive Components Using Reference Drawings and Parts Lists
- Chapter 3 Using the Keypad/Display to Program, Monitor, and Control the Drive
- Chapter 4 Identifying Parameter Defaults For Carrier Drives
- Chapter 5 Verifying the Installation
- Chapter 6 Troubleshooting the Drive
- 6.1 Test Equipment Needed To Troubleshoot
- 6.2 Verifying That DC Bus Capacitors Are Discharged
- Step 1. Turn off and lock out input power. Wait five minutes.
- Step 2. Verify that there is no voltage at the drive’s input power terminals.
- Step 3. Measure the DC bus potential with a voltmeter while standing on a non-conductive surface and wearing insulated gloves (1...
- Step 4. Once the drive has been serviced, reapply input power.
- Figure 6.1 - DC Bus Voltage Terminals (414 Amp Drives)
- Figure 6.2 - DC Bus Voltage Terminals (500 Amp and 643 Amp Drives)
- 6.3 Checking the Power Modules and Motor with Input Power Off
- Step 1. Turn off and lock out input power. Wait five minutes.
- Step 2. Verify that there is no voltage at the drive’s input power terminals.
- Step 3. Check the DC bus potential with a voltmeter as described in section 6.2 to ensure that the DC bus capacitors are discharged.
- Step 4. Disconnect the motor from the drive.
- Step 5. Check all AC line and DC bus fuses.
- Step 6. If a fuse is open, use a multimeter to check the input diodes and output IGBTs. See table 6.1.
- Step 7. Check motor impedance.
- Step 8. Reconnect the motor to the drive.
- Step 9. Reapply input power.
- Table 6.1 - Resistance Checks
- 6.4 Troubleshooting the Drive Using Error Codes
- 6.5 Identifying Fatal Fault Codes and Recovering
- 6.6 Indentifying PMC Board Fault Codes and Recovering
- 6.7 Resetting a Checksum (CHS) Fault
- Step 1. Press and hold STOPIRESET, PROGRAM, and DOWN ARROW for 5 to 10 seconds. A PUn error should appear.
- Step 2. Press PROGRAM. P.--- is displayed.
- Step 3. Press ENTER. P.000 is displayed.
- Step 4. Press UP ARROW until P.006 is displayed.
- Step 5. Press ENTER.
- Step 6. Press UP ARROW until 107 is displayed.
- Step 7. Press ENTER.
- Step 8. Press UP ARROW until P.048 is displayed.
- Step 9. Press ENTER.
- Step 10. Press UP or DOWN ARROW to select UEC or U-H mode.
- Step 11. Press ENTER. Observe SELF is displayed briefly.
- Step 12. Press UP or DOWN ARROW until P.006 is displayed.
- Step 13. Press ENTER.
- Step 14. Press UP ARROW until 75 is displayed.
- Step 15. Press ENTER.
- Step 16. Press UP ARROW until R998 is displayed.
- Step 17. Press ENTER.
- Step 18. Press UP ARROW until ON is displayed.
- Step 19. Press ENTER.
- Step 20. Press UP ARROW until P.999 is displayed. Depending on software version, the display may show PUGH or P.999. If PUCH is displayed, wait for 0 to display. The procedure is complete. If P.999 is displayed, continue with step 21.
- Step 21. Press ENTER.
- Step 22. Press UP ARROW until the correct power unit current and voltage rating code appears. The codes are as follows:
- Step 23. Press ENTER. PUCH should appear briefly.
- DIF Documentation Improvement Form