Artesyn ATCA-8330 Installation and Use (April 2015) Instruction Manuals and User Guides
We have 1 Instruction Manual and User Guide for ATCA-8330 Installation and Use (April 2015) Artesyn
Manuals 
| Recognized languages: | English |
|---|---|
| Pages: | 236 |
| Size: | 13.95 MB |
Show table of contents
Document Outline
- ATCA-8330
- Contents
- About this Manual
- Safety Notes
- Sicherheitshinweise
- Introduction
- Hardware Preparation and Installation
- Controls, Indicators, and Connectors
- BIOS
- 4.1 Introduction
- 4.2 Accessing the Blade Using the Serial Console Redirection
- 4.3 Changing Configuration Settings
- 4.4 Boot Options
- 4.5 IPMI Boot Parameter
- 4.6 Restoring BIOS Default Settings
- 4.7 BIOS Setup Configuration
- 4.8 Restoring BIOS Default Settings
- 4.9 IPMI Support
- 4.10 Watchdog Support
- 4.11 BIOS Error Logging
- 4.12 Upgrading the BIOS
- 4.13 BIOS Status Codes
- Functional Description
- 5.1 Block Diagram
- 5.2 Processor
- 5.3 Memory
- 5.4 DSP Farm
- 5.5 Platform Controller Hub (PCH)
- 5.6 Firmware Flashes
- 5.7 Ethernet Ports
- 5.8 MO297 SlimSATA Embedded Solid State Disc (SSD)
- 5.9 BIOS
- 5.10 IPMC
- 5.11 Serial Redirection
- 5.12 Serial Over LAN
- 5.13 Control Logic
- 5.14 Front Board Faceplate
- 5.15 Faceplate Serial Interfaces
- 5.16 USB 2.0 Interfaces
- 5.17 LPC Interface
- 5.18 Trusted Platform Module
- 5.19 Real Time Clock
- 5.20 SMBus
- Programmable Logic
- Intelligent Peripheral Management Controller
- 7.1 Functional Overview
- 7.2 Firmware Architecture
- 7.3 HPM.1 Components
- 7.4 Sensors
- 7.5 POST
- 7.6 BIOS Boot Configuration Parameters
- 7.7 Asynchronous Event Notification
- 7.8 Fail Safe Logic and Watchdog Support
- 7.9 Payload Interface
- 7.10 Payload Boot Bank Selection
- 7.11 Settable Graceful Shutdown Timeout
- 7.12 Local System Event Log
- 7.13 IPMI Hardware Watchdog
- Serial Over LAN
- Supported IPMI Commands
- 9.1 Standard IPMI Commands
- 9.2 PICMG 3.0 Commands
- 9.3 Artesyn Embedded Technologies Specific Commands
- 9.4 Pigeon Point Specific Commands
- 9.4.1 Get Status Command
- 9.4.2 Get Serial Interface Properties Command
- 9.4.3 Set Serial Interface Properties Command
- 9.4.4 Get Debug Level Command
- 9.4.5 Set Debug Level Command
- 9.4.6 Get Hardware Address Command
- 9.4.7 Set Hardware Address Command
- 9.4.8 Get Handle Switch Command
- 9.4.9 Set Handle Switch Command
- 9.4.10 Get Payload Communication Time-Out Command
- 9.4.11 Set Payload Communication Time-Out Command
- 9.4.12 Enable Payload Control Command
- 9.4.13 Disable Payload Control Command
- 9.4.14 Reset IPMC Command
- 9.4.15 Hang IPMC Command
- 9.4.16 Graceful Reset Command
- 9.4.17 Get Payload Shutdown Time-Out Command
- 9.4.18 Set Payload Shutdown Time-Out Command
- 9.4.19 Get Module State Command
- 9.4.20 Enable Module Site Command
- 9.4.21 Disable Module Site Command
- 9.4.22 Reset Carrier SDR Repository Command
- FRU Information and Sensor Data Records
- A Replacing the Battery
- B Related Documentation