Quickspecs – HP xw8200 User Manual
Page 4
4th Hard Disk Drive
One of the following
Windows XP
Red Hat Linux
Serial ATA 3Gb/s Hard Drives
4th hard drive, 80 GB SATA 3.0Gb/s 7200 rpm Hard Drive
32-Bit, 64-Bit
WS3, WS4
4th hard drive, 160 GB SATA 3.0Gb/s 7200 rpm Hard Drive
32-Bit, 64-Bit
WS3, WS4
4th hard drive, 250 GB SATA 3.0Gb/s 7200 rpm Hard Drive (8
MB cache)
32-Bit, 64-Bit
WS3, WS4
4th hard drive, 500 GB SATA 3.0Gb/s 7200 rpm Hard Drive (8
MB cache)
32-Bit, 64-Bit
WS3, WS4
Serial ATA 1.5Gb/s Hard Drives
4th hard drive, 74 GB SATA 1.0Gb/s 10K rpm Hard Drive (8
MB cache)
32-Bit
WS3, WS4
Ultra320 SCSI Hard Drives
4th hard drive, 73 GB Ultra320 SCSI 10K rpm Hard Drive
32-Bit, 64-Bit
7.2, 7.3, WS3,
WS4
4th hard drive, 300 GB Ultra320 SCSI 10K rpm Hard Drive
32-Bit, 64-Bit
7.2, 7.3, WS3,
WS4
4th hard drive, 73 GB Ultra320 SCSI 15K rpm Hard Drive
32-Bit, 64-Bit
7.2, 7.3, WS3,
WS4
5th*** Hard Disk Drive
One of the following
Windows XP
Red Hat Linux
Ultra320 SCSI Hard Drives
5th hard drive, 73 GB Ultra320 SCSI 10K rpm Hard Drive
32-Bit, 64-Bit
7.2, 7.3, WS3,
WS4
5th hard drive, 300 GB Ultra320 SCSI 10K rpm Hard Drive
32-Bit, 64-Bit
7.2, 7.3, WS3,
WS4
5th hard drive, 73 GB Ultra320 SCSI 15K rpm Hard Drive
32-Bit, 64-Bit
7.2, 7.3, WS3,
WS4
***NOTE: Fourth hard drive must be SCSI.
Factory Integrated
RAID
Windows XP
Red Hat Linux
RAID 0 Configuration – Striped Array
32-Bit, 64-Bit
7.2, 7.3, WS3,
WS4
RAID 0 Configuration - Data Array
32-Bit, 64-Bit
7.2, 7.3, WS3,
WS4
RAID 1 Configuration – Mirrored Array
32-Bit, 64-Bit
7.2, 7.3, WS3,
WS4
NOTE: Requires 2 identical hard drives (speeds, capacity,
interface)
Drive controllers
Windows XP
Red Hat Linux
LSI 3041E 4-port SAS/SATA RAID Card *
32-Bit, 64-Bit
WS3, WS4
Cable, 5 Part SCSI (required if 1st drive is SATA and any of the
other drives are SCSI)
Ultra320 back panel connect (uses HDCI connectors)
NOTE: * No Support for SATA 1.5Gb/s non-NCQ hard drive RAID arrays. 48-Bit LBA is required.
QuickSpecs
HP xw8200 Workstation
Standard Features - Custom Components
DA - 11976 Worldwide QuickSpecs — Version 42 — 5.25.2007
Page 4