Quickspecs, Hp bladesystem c3000 enclosure – HP Hewlett-Packard BladeSystem Enclosure c3000 User Manual

Page 34

Mixed Configuration – Full Height and Half Height Population

Mixed Configuration – Full Height and Half Height Population
The c3000 enclosure is divided into 2 zones or quadrants by the horizontal (vertical on Tower model) support metalwork. Zone 1
includes bays 1, 2, 4, & 5; and Zone 2 contains bays 3, 4, 7, & 8. Within each zone a removable divider is used to support half
height devices. To install a full-height blade in any zone this divider must be removed. An optional mini-divider support bracket is
included with every c3000 enclosure. As a consequence of using the mini-divider in the Zone 2, this zone can only contain one full
height blade and 2 half-height blades. Zone 1 can contain either 4 half-height blades, or by removing the divider, it can contain 2
full-height blades.

NOTE:

NOTE: Please read the RTF card (included with each c3000 enclosure) and the "HP BladeSystem c3000 Setup and Installation
Guide" for more information on using bay dividers and the mini-divider for mixed configurations.

NOTE:

NOTE: Storage or tape blades can be installed in the same zone as both full-height and half-height blades, a bracket ships with
each SB40c that allows a half-height blade to be mounted to the left side of a storage or tape blade.

NOTE:

NOTE: In this case, the SB40c or tape blade cannot be removed without first removing the half height blade and mounting bracket.

NOTE:

NOTE: For Mixed configurations of full height and half height population rules; please see the c3000 Enclosure installation and
users guide at:

http://h71028.www7.hp.com/enterprise/cache/316682-0-0-0-121.html

Enclosure Unit –

Enclosure Unit –
Rack Model

Rack Model

Dimensions

Dimensions (H x W x D)
(with bezel)

10.4 x 19.1 x 32.977 in (265 x 485 x 835 mm)

Weight

Weight
(approximate)

Maximum
(one enclosure with 8
blades and 4 interconnects
installed)

300 lb (136 kg)

Minimum
(one enclosure without
blades and interconnects)

130 lb (59 kg)

Input Requirements

Input Requirements
(per AC power supply)

Rated Line Voltage

90 –

–

– 132 VAC

180 –

–

– 264 VAC

Rated Input Current

9.3 A (at 100 VAC)
9.7 A (at 120VAC)
7.8 A (at 200 VAC)
7.2 A (at 208 VAC)
6.8 A (at 220 VAC)
6.2 A (at 240 VAC)

Rated Input Frequency

47 to 63 Hz

BTU Rating

Maximum per power
supply

2728 BTU/hr (at 100 VAC)
3069 BTU/hr (at 120VAC)
4092 BTU/hr (at 200 to 240 VAC)

Power Specifications

To review typical system power ratings use the Power Calculator which is
available via the online tool located at URL:

www.hp.com/go/bladesystem/powercalculator

Power Supply Output

Power Supply Output
(per power supply)

Rated Steady-State Power 800 W (at 100 VAC)

900 W (at 120 VAC)
1200 W (at 200 to 240 VAC)

Maximum Peak Power

880 W (at 100 VAC)
990 W (at 120 VAC)
1350 W (at 200 to 240 VAC)

QuickSpecs

HP BladeSystem c3000 Enclosure

Technical Specifications

DA - 12790 Worldwide — Version 12 — July 14, 2008

Page 34