Philips T-Line 65BDL3552T 65" 4K Digital Signage Touchscreen Display User Manual

Page 49

65BDL3552T/75BDL3552T/86BDL3552T

• {Secondary}

- Designate this display as the secondary

display. This display can not be operated by the remote
control, and will only receive the control signal from the
primary display via RS232C connection.

• {Lock All}

{Lock all but Volume}

{Lock all but Power}

{Lock all except PWR & VOL}

- Lock the remote control

function of this display. To unlock, press and hold the
[Info] button on the remote control for more than 6
seconds. It will exit from OSD menu automatically after
locking IR.

No warning message will be shown when IR control is
locked.

Keyboard control

Choose to enable or disable the display keyboard (control
buttons) function.

• {Unlock}

- Enable the keyboard function.

• {Lock All}

{Lock all but Volume}

{Lock all but Power}

{Lock all except PWR & VOL}

- Disable the keyboard

function depending on the option you selected.

NOTE:

“Keyboard Control Lock Mode” This function

completely disables the access to all Keyboard
Control functions. To enable or disable the
keyboard control lock, press both [VOL+] and [UP]
buttons and hold down continuously for more than
3 (three) seconds.

Off Timer

Set automatic power off time (in hours).

Schedule

1. Default start time and end time are 00:00.
2. Start time and End time must be from the same date of
the schedule.

Schedule

Schedule list

Enable

Start time
End time
Input
Playlist
Days of the week
Every week

Back

SAVE

■

Set lifecycle.

Back:

■

Exit without saving changes.

Save:

■

Save schedule data.

HDMI with One Wire

CEC control.

• {Off}

- Disable CEC.(Default)

• {On}

- Enable CEC.

The following features are supported:
• One Touch Play allows devices to switch the display to

use it as the active source when playback starts.

• System Standby enables users to switch multiple devices

to standby mode with the press of one button (HDMI
with One Wire Power off is On).

Auto signal detection

This function allows the system to detect and display the
available signal sources automatically.
Conditions for Auto Signal Detection:
1. Sub mode is “Off”
2. After showing Logo
3. Power state is not Power Off
The options are:

{Off}

{All}

{Failover}

{Off}

: Disable Auto signal detection

{All}

: OPS -> HDMI1 -> HDMI2 -> HDMI3 -> HDMI4 ->

DisplayPort -> DVI-D ->USB-TypeC -> VGA -> Media Player
-> SmartCMS -> Home

{Failover}:

Failover 1: OPS(default)

Failover 2: OPS(default)

Faliover 3: OPS(default)

Failover 4: OPS(default)

Failover 5: OPS(default)

Failover 6: OPS(default)

Failover 7: OPS(default)

Failover 8: OPS(default)

Failover 9: OPS(default)

Failover 10: OPS(default)

Failover 11: OPS(default)

Failover 12: OPS(default)

The Failover behavior is when signal is lost, the display will
go to the next available source which is defined in priority
list in order.
Please note, the followings will suspend failover, and the
failover will resume when signal is lost again.
-

Boot On Source : When the display powers on, it will go
to the source defined in this OSD option.

Scheduler: When the display powers on by scheduler,
it will go to the corresponding source according to the
current time.

User operation: No matter what current source it is,
when user manually changes source, the failover will
suspend.

To make sure failover starts from the 1

priority source after

powering on, please set the 1

priority source as boot on

source too.