Philips T-Line 65BDL3552T 65" 4K Digital Signage Touchscreen Display - Manual (Page 47)

65BDL3552T/75BDL3552T/86BDL3552T
35
Auto Adjust
Press “Set” to detect and adjust H position, V position,
Clock, Phase automatically.
NOTE: This item applies to
VGA input only.
Screen reset
Reset all settings in the Screen menu to factory preset
values.
6.2.3. Audio menu
Picture
Screen
Audio
Configuration
Advanced
Android Settings Balance
Treble
Bass
Volume
Audio Out (Line Out)
Maximum Volume
Minimum Volume
Mute
Audio source
Audio reset
Audio Out Sync
Speaker setting
50
50
50
20
20
100
0
Off
Digital
Action
Off
On
Balance
Adjust to emphasize left or right audio output balance.
Treble
Adjust to increase or decrease higher-pitched sounds.
Bass
Adjust to increase or decrease lower-pitched sounds.
Volume
Adjust the volume.
Audio out (Line out)
Adjust to increase or decrease line out output level.
Maximum volume
Adjust your own limitation for the maximum volume setting.
This stops the volume at the sound level you set.
Minimum volume
Adjust your own limitation for the minimum volume setting.
Mute
Turn the mute function on/off.
Audio source
Select the audio input source. Audio output is not
supported when there is no video signal.
• {Analog} - Audio from audio input. (Audio from OPS
audio input when OPS is selected as source)
• {Digital} - Audio from video input source. (VGA and DVI
are not supported)
Audio reset
Reset all settings in the Audio menu to factory preset values
for current source.
Audio Out Sync
Line out volume sync with Volume.
• {On} - Enable the function.
• {Off} - Disable the function and Audio Out Volume will
be grayed out.
Speaker Setting
Enable/disable speaker.
NOTE: This function is available only when “Audio Out
Sync” is on.
6.2.4. Configuration menu
Picture
Screen
Audio
Configuration
Advanced
Android Settings Switch on state
Panel saving
RS232 routing
Boot on source
WOL
DP version
HDMI version
Information OSD
Monitor ID
Heat status
Configuration reset
Factory reset
Force on
Action
RS232
Action
Off
1.1
1.4
10
Action
25.00°C 77.00°F
Action
Action
Switch on state
Select the display status that will be applied when you
connect the power cord next time.
• {Power off} - The display will remain off when the power
cord is connected to a wall outlet.
• {Forced on} - The display will turn on when the power
cord is connected to a wall outlet.
• {Last status} - The display will return to the previous
power status (on/off mode/standby mode) when
removing and replacing the power cord.
Panel saving
Choose to enable the panel saving functions and thus
reduce the risk of image persistence or ghost imaging.
• {Brightness} - Select {On} and the image brightness will
be reduced to 30%.
• {Pixel shift} - Select the time interval ( {Auto} / {10 ~ 900}
seconds ) for the display to slightly expand the image
size and shift the position of pixels in four directions (up,
down, left, or right). Activating Pixel Shift will disable H
Position, V Position and Zoom Mode in the screen menu.
NOTES:
• Auto is 60 seconds.
• Only supports external input source (HDMI, VGA, DP,
OPS, DVI)
RS232 routing
Select the network control port.
Choose from:
{RS232} / {LAN->RS232} / {CardOPSRS232
(OPS model only)} / {STANDALONE} .
Boot on source
Choose to select source when booting up.
Last Input : keep last input when booting up.
Input: select input source(follow S12 Input source) when
booting up.
Playlist: select playlist index for Media player, Browser.
0: No playlist. Same as switching source from OSD.