Whelen 295SDA1 - Manual (Page 10)

Page 10
OR…
• Press and release the lighting momentary switch 5 to change the tone
produced by speaker 2.
• Each time a switch is pressed and released, the next available tone will
be broadcast on the corresponding speaker.
AND…
• The other speaker will shut off for 2 seconds so that the new tone can
be clearly identified.
• When the desired tone is generated, it is automatically saved in that
switch position for that speaker.
To change the override tone for the WAIL, YELP and TONE 3
switch positions:
• Activate the switch position that you wish to change.
• Press and release the MANUAL switch to produce it’s override tone.
• Press and release the lighting momentary switch 4 to change the tone
produced by speaker 1.
OR…
• Press and release the lighting momentary switch 5 to change the tone
produced by speaker 2.
• Each time a switch is pressed and released, the next available tone will
be broadcast on the corresponding speaker.
AND…
• The other speaker will shut off for 2 seconds so that the new tone can
be clearly identified.
• When the desired tone is generated, it is automatically saved as the
override tone in that switch position for that speaker.
To change the tones in a HANDS FREE cycle position
(STANDBY switch):
• Activate the STANDBY switch.
• Press and release the MANUAL switch to advance to the HAND FREE
cycle position that you want to change.
• Press and release the lighting momentary switch 4 to change the tone
produced by speaker 1.
OR…
• Press and release the lighting momentary switch 5 to change the tone
produced by speaker 2.
• Each time a switch is pressed and released, the next available tone will
be broadcast on the corresponding speaker.
AND…
• The other speaker will shut off for 2 seconds so that the new tone can
be clearly identified.
• When the desired tone is generated, it is automatically saved for that
HAND FREE cycle position for that speaker.
To change the tone for the MANUAL and AIRHORN switch:
• Press and hold the MANUAL or AIRHORN switch.
• Press and release the lighting momentary switch 4 to change the tone
produced by speaker 1.
OR…
• Press and release the lighting momentary switch 5 to change the tone
produced by speaker 2.
• Each time a switch is pressed and released, the next available tone will
be broadcast on the corresponding speaker.
AND…
• The other speaker will shut off for 2 seconds
so that the new tone can be clearly
identified.
• When the desired tone is generated, it is
automatically saved for the chosen switch
for that speaker.
Adjusting Radio Levels :
Wail coast
Phased Wail coast
Wail Stop
Phased Wail Stop
Mechanical coast
Phased Mechanical coast
Mechanical stop
Phased Mechanical stop
Tone list for the MANUAL button:
··
·
··
·
··
Tone List for Airhorn button:
Tone off
Airhorn
Airhorn low
··
·
SW1
ON
ON
OFF
SW2
ON
ON
ON
SW3
ON
ON
ON
SW4
ON
OFF
ON
Operation
Normal operations
Programming lighting
Programming Siren tones
Any other Dip Switch setting combinations are not valid
and are not recomended.
Di Switch Settin s p g :
Tone off
Wail
Phased wail
Wail 2
Yelp
Phased Yelp
Yelp 2
Yelp 249
Piercer
Hilo
Mechanical
Phased Mechanical
Mechanical 2
Warble
Phased Warble
Woop
Phased Woop
Wail Yelp combo
Wail Yelp Combo 2
Tone list for Wail, Yelp & Tone 3 buttons and their override tones, and all hf positions:
··
··
·
··
··
·
··
··
·
··
··
RADIO
VOL
PA
VOL
To adjust RADIO or PA volume,
use a small flat blade
screwdriver.