Whelen SK01AA - Manual

Page 1
View from Outside of the Fender
8 - 32 X 1/2" PHILLIPS
PAN HEAD METAL SCREW
Fig. 1
INSERT FRONT OF HOUSING.
MOUNTING CLIP MUST CATCH
INSIDE EDGE OF BODY.
©2012 Whelen Engineering Company Inc.
Form No.14577 (033012)
Automotive:
Lightheads
Installation Guide:
SideKick™ Super-LED® Fender Lights
2012 - 2013 Ford Police Interceptor Sedan
®
ENGINEERING COMPANY INC.
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Fax: (860) 526-4078
Internet: www.whelen.com
Sales e-mail: [email protected]
Canadian Sales e-mail: [email protected]
Customer Service e-mail: [email protected]
For warranty information regarding this product, visi85ww.whelen.com/warranty
Installation:
1. Remove the vent panel from the vehicle per
manufacturers instructions and install the
supplied clip nut onto the fender on the vent rear
mounting hole.
2. Install the ION™ lighthead into the SideKick™
panel using the 2 supplied washer head screws
(Fig. 2).
3. Extend the lighthead wires into the fender to the power source and
install the SideKick™ panel by first inserting the front into the fender
opening so that the 2 mounting clips on the SideKick™ grab the
inside of the fender (Figs. 1 & 2).
4. Next swing the rear of the SideKick™ toward the fender so that the
rear mounting hole lines up with the clip nut you installed and secure
it with the supplied 8 - 32 X 1/2” Phillips Pan Head Metal Screw.
IMPORTANT: It is the responsibility of the installation
technician to make sure that the installation and operation of
this product will not interfere with or compromise the operation
or efficiency of any vehicle equipment!
INSTALL
CLIP NUT
View from Outside of the Fender
8 - 32 X 1/2" PHILLIPS
PAN HEAD METAL SCREW
Fig. 1
INSERT FRONT OF HOUSING.
MOUNTING CLIP MUST CATCH
INSIDE EDGE OF BODY.
©2012 Whelen Engineering Company Inc.
Form No.14577 (033012)
Automotive:
Lightheads
Installation Guide:
SideKick™ Super-LED® Fender Lights
2012 - 2013 Ford Police Interceptor Sedan
®
ENGINEERING COMPANY INC.
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Fax: (860) 526-4078
Internet: www.whelen.com
Sales e-mail: [email protected]
Canadian Sales e-mail: [email protected]
Customer Service e-mail: [email protected]
For warranty information regarding this product, visi85ww.whelen.com/warranty
Installation:
1. Remove the vent panel from the vehicle per
manufacturers instructions and install the
supplied clip nut onto the fender on the vent rear
mounting hole.
2. Install the ION™ lighthead into the SideKick™
panel using the 2 supplied washer head screws
(Fig. 2).
3. Extend the lighthead wires into the fender to the power source and
install the SideKick™ panel by first inserting the front into the fender
opening so that the 2 mounting clips on the SideKick™ grab the
inside of the fender (Figs. 1 & 2).
4. Next swing the rear of the SideKick™ toward the fender so that the
rear mounting hole lines up with the clip nut you installed and secure
it with the supplied 8 - 32 X 1/2” Phillips Pan Head Metal Screw.
IMPORTANT: It is the responsibility of the installation
technician to make sure that the installation and operation of
this product will not interfere with or compromise the operation
or efficiency of any vehicle equipment!
INSTALL
CLIP NUT
View from the Inside of the Fender Fig. 2
MOUNTING CLIP MUST REST
ON INSIDE EDGE OF BODY
OPENING 6 - 32 X 5/16 WASHER HD SCREW
(LIGHTHEAD TO BRACKET)
SECURE REAR OF
HOUSING TO CLIP
NUT
View from the Inside of the Fender Fig. 2
MOUNTING CLIP MUST REST
ON INSIDE EDGE OF BODY
OPENING 6 - 32 X 5/16 WASHER HD SCREW
(LIGHTHEAD TO BRACKET)
SECURE REAR OF
HOUSING TO CLIP
NUT