Whelen UHF2150A User Manual

Automotive: flashers

Page 1

Installation Guide:

UHF2150A High Beam Flasher

IMPORTANT NOTES!

• The use of a flashing headlight system may be

regulated by state, county, or municipal authorities. It
is the responsibility of the end user to comply with
these regulations.

• It is the responsibility of the installer to make sure that

the high beam and low beam filaments of a dual
filament bulb never come on together. The excessive
heat generated by this condition will melt the headlight
assembly. The brown disable wire may have to be
connected to the parking lights or the low beams to
override the flasher and prevent both filaments from
coming on simultaneously.

• The installation of a headlight flasher system requires

a modification to the standard headlight wiring
harness. This modification may effect the warranty of
your vehicle. It is the responsibility of the end user to
verify the warranty conditions with the vehicle
manufacturer. Also, the use of a headlight flasher may
shorten the high beam bulb life.

• Before attempting the installation of the UHF2150A

headlight flasher, thoroughly read and understand
instructions and steps shown below!

• Disconnect the battery from the electrical system

before attempting any part of this installation!

• All customer supplied wires that connect to the

positive terminal of the battery must be sized to supply
at least 125% of the maximum operating current and
FUSED at the battery to carry the load. DO NOT USE
CIRCUIT BREAKERS WITH THIS PRODUCT!

Installation
There are two different switching methods used to
activate the headlights/parking lights in a motor vehicle;
Positive-Side Switching and Ground-Side Switching.
For example, the headlights may use Positive-Side
switching, while the parking lights may use Ground-Side
switching. Before installing this product, it will be
necessary to contact the vehicle manufacturer to
determine which methods are used. After the proper
methods have been established, follow the appropriate
procedure, based on the method used by the headlight
system.

If Your Headlights are Positive-Side Switched...
1.

Mount the flasher in the engine compartment near
the headlights.

GROUND - Connect the BLACK wire to the
vehicle’s chassis ground.

NIGHT CUTOUT - BROWN - Connect this wire to
the parking light or low beam circuit to disable the
flasher when headlights are on. This is to prevent
both filaments in a dual filament bulb from being on
simultaneously (or if required in your jurisdiction).

High Beam Override - Splice the WHITE wire into
the circuit that the BLUE/WHITE wire is to be
connected to in step 5. Splice the WHITE/BLACK
wire into the circuit that the ORANGE wire is to be
connected to in step 7.

Driver Side Lamp - Locate the wire that connects the
driver side high beam lamp to the headlight dimmer
switch. Cut this wire at a point 3 inches away from
the lamp. Connect the BLUE wire to the wire that
connects to the high beam lamp. Connect the
WHITE/BLUE wire to the wire that connects to the
headlight dimmer switch.

Passenger Side Lamp - Locate the wire that
connects the passenger side high beam lamp to the
headlight dimmer switch. Cut this wire at a point 3
inches away from the lamp. Connect the YELLOW
wire to the wire that connects to the high beam
lamp. Connect the WHITE/YELLOW wire to the wire
that connects to the headlight dimmer switch.

On/Off Control - Connect the ORANGE wire to a
+12VDC power switch (200 mA MIN.(user
supplied)).

Lamp Feed - Connect the RED wire, fused at 15
Amps (customer supplied) to the POS (+) battery
terminal.

If Your Headlights are Ground-Side Switched...

NOTE: Daytime Running Lights may control the +12VDC
supplied to the headlights. Before proceeding, unplug
each headlight and verify that while the vehicle is run-
ning, +12VDC is being provided. This flasher will not
operate properly if +12VDC is not available.

ENGINEERING COMPANY INC.

51 Winthrop Road
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Fax: (860) 526-4078
Internet: www.whelen.com
Sales e-mail: [email protected]
Canadian Sales e-mail: [email protected]
Customer Service e-mail: [email protected]

Automotive:

Flashers