KEPCO MST 488 Programmer - Manual (Page 59)

MST 488-27 013004
B-11
STAT:QUES:INST:ISUM:ENAB
B.39
STATus:QUEStionable:INSTrument:ISUM:ENABle
COMMAND
Syntax: Short Form: STAT:QUES:INST:ISUM:ENAB
Long Form: STATus:QUESionable:INSTrument:ISUM:ENABle
Description: Programs Questionable Instrument ISUM Enable Register (see Table B-3).The Questionable
Instrument ISUM Enable Register is a mask which determines which conditions are allowed to set the
Questionable Instrument ISUM Register for the selected channel. This command requires that the
SCPI compliant mode of operation for multiple logical instruments be enabled first by sending
SYST:SET S1 (see PAR. B.48).
STAT:QUES:INST:ISUM:ENAB?
B.40
STATus:QUEStionable:INSTrument:ISUM:ENABle?
QUERY
Syntax: Short Form: STAT:QUES:INST:ISUM:ENAB?
Long Form: STATus:QUESionable:INSTrument:ISUM:ENABle?
Return Value: actual register value
Description: Reads ISUM Enable Register (see Table B-3). Unit returns value of ISUM Enable Register for
selected channel. This command requires that the SCPI compliant mode of operation for multiple logi-
cal instruments be enabled first by sending SYST:SET S1 (see PAR. B.48).
B.41
SYSTem:COMMunication:GPIB:ADDRess
COMMAND
SYST:COMM:GPIB:ADDR
Syntax: Short Form: SYST:COMM:GPIB:ADDR 1 to 30
Long Form: SYSTem:COMMunication:GPIB:ADDRess 1 to 30
Description: Sets selected power supply GPIB address.
B.42
SYSTem:COMMunication:SERial:BAUD
COMMAND
SYST:COMM:SER:BAUD
Syntax: Short Form: SYST:COMM:SER:BAUD {19200 | 9600 | 4800 | 2400}
Long Form: SYSTem:COMMunication:SERial:BAUD {19200 | 9600 | 4800 | 2400}
Description: Sets the unit to operate at the specified baud rate.
B.43
SYSTem:COMMunication:SERial:ECHO
COMMAND
SYST:COMM:SER:ECHO
Syntax: Short Form: SYST:COMM:SER:ECHO {ON | OFF}
Long Form: SYSTem:COMMunication:SERial:ECHO {ON | OFF}
Description: Enables (ON) or disables (OFF) echo mode (see PAR. 3.3.3.1) Sending ON causes all subsequent
characters to be echoed back. Sending OFF turns off the character echo after the nest line terminator
character. The *RST command has no effect on echo status
B.44
SYSTem:COMMunication:SERial:PACE
COMMAND
SYST:COMM:SER:PACE
Syntax: Short Form: SYST:COMM:SER:PACE {NONE | XON}
Long Form: SYSTem:COMMunication:SERial:PACE {NONE | XON}
Description: Enables (XON) or disables (NONE) data flow control via the serial interface (see PAR. 3.3.3.3)
B.45
SYSTem:COMMunication:SERial:PROMpt
COMMAND
SYST:COMM:SER:PROM
Syntax: Short Form: SYST:COMM:SER:PROM {ON | OFF}
Long Form: SYSTem:COMMunication:SERial:PROMpt {ON | OFF}
Description: Enables (ON) or disables (OFF) prompt (see PAR. 3.3.3.3). Sending ON causes the unit to return >
character after the command is parsed.
B.46
SYSTem:ERRor[:NEXT]?
QUERY
SYST:ERR?
Syntax: Short Form: SYST:ERR[:NEXT]? Long Form: SYSTem:ERRor[:NEXT]?
Return Value: