KEPCO MST 488 Programmer - Manual (Page 10)

ii
MST488-27 SVC 013004
TABLE OF CONTENTS
SECTION PAGE
APPENDIX A - IEEE 488.2 COMMAND/QUERY DEFINITIONS
A.1 Introduction ............................................................................................................................................. A-1
A.2 *CLS — Clear Status Command .......................................................................................................... A-1
A.3 *ESE — Standard Event Status Enable Command................................................................................ A-1
A.4 *ESE? — Standard Event Status Enable Query..................................................................................... A-1
A.5 *ESR? — Event Status Register Query................................................................................................. A-2
A.6 *IDN? — Identification Query.................................................................................................................. A-2
A.7 *OPC — Operation Complete Command ............................................................................................... A-2
A.8 *OPC? — Operation Complete Query .................................................................................................... A-3
A.9 *OPT? — Options Query ........................................................................................................................ A-3
A.10 *RST — Reset Command....................................................................................................................... A-4
A.11 *SRE — Service Request Enable Command ........................................................................................ A-4
A.12 *SRE? — Service Request Enable Query .............................................................................................. A-4
A.13 *STB? — Status Byte Register Query ................................................................................................... A-4
A.14 *TRG — Trigger Command ................................................................................................................... A-4
A.15 *TST? — Self Test Query ....................................................................................................................... A-5
A.16 *WAI — Wait-to-Continue Command ..................................................................................................... A-5
APPENDIX B - SCPI COMMAND/QUERY DEFINITIONS
B.1 Introduction ............................................................................................................................................. B-1
B.2 INITiate[:IMMediate] Command .............................................................................................. B-1
B.3 INITiate:CONTinuous Command................................................................................................. B-1
B.4 INITiate:CONTinuous Query ....................................................................................................... B-2
B.5 INSTrument:CATalog Query.......................................................................................................... B-2
B.6 INSTrument[:NSELect] Command .............................................................................................. B-2
B.7 INSTrument[:SELect] Command ................................................................................................ B-2
B.8 INSTrument[:SELect]? Query..................................................................................................... B-3
B.9 INSTrument:STATe Command........................................................................................................ B-3
B.10 MEASure[:SCALar]:CURRent[:DC]? Query............................................................................. B-3
B.11 MEASure[:VOLTage][:SCALar][:DC]? Query ........................................................................ B-4
B.12 OUTPut[:STATe] Command............................................................................................................. B-4
B.13 OUTPut[:STATe] Query ................................................................................................................... B-4
B.14 [SOURce:]CURRent[:LEVel][:IMMediate][:AMPlitude] Command........................... B-4
B.15 [SOURce:]CURRent[:LEVel][:IMMediate][:AMPlitude] Query.................................. B-4
B.16 [SOURce:]CURRent:[:LEVel]TRIGgered[:AMPlitude] Command .............................. B-5
B.17 [SOURce:]CURRent:[:LEVel]TRIGgered[:AMPlitude]? Query .................................... B-5
B.18 [SOURce:]VOLTage[:LEVel][:IMMediate][:AMPlitude] Command........................... B-6
B.19 [SOURce:]VOLTage[:LEVel][:IMMediate][:AMPlitude]? Query ............................... B-6
B.20 [SOURce:]VOLTage:[:LEVel]TRIGgered[:AMPlitude] Command................................ B-6
B.21 [SOURce:]VOLTage:[:LEVel]TRIGgered[:AMPlitude]? Query .................................... B-6
B.22 [SOURce:]FUNCtion:MODE Command ......................................................................................... B-7
B.23 STATus:OPERation:CONDition Query....................................................................................... B-7
B.24 STATus:OPEReration:ENABle Command .................................................................................. B-7
B.25 STATus:OPEReration:ENABle? Query....................................................................................... B-7
B.26 STATus:OPERation[:EVENt] Query ........................................................................................... B-7
B.27 STATus:PRESet Command ............................................................................................................... B-7
B.28 STATus:QUEStionable[:EVENt]? Query.................................................................................. B-8
B.29 STATus:QUEStionable:CONDition? Query............................................................................. B-9
B.30 STATus:QUEStionable:ENABle Command................................................................................ B-9
B.31 STATus:QUEStionable:ENABle? Query .................................................................................... B-9
B.32 STATus:QUEStionable:INSTrument[1]? Query ................................................................... B-9
B.33 STATus:QUEStionable:INSTrument2? Query ........................................................................ B-9
B.34 STATus:QUEStionable:INSTrument[1]:ENABle Command .............................................. B-10
B.35 STATus:QUEStionable:INSTrument[1]:ENABle Query..................................................... B-10