Precision Digital PD941 - Manual (Page 50)

ConsoliDator Multi-Channel Controller Instruction Manual
50
Table 5. Relay Channels Register Addresses
Address (offset from 40000)
Description Data Type Rly. 1 Rly. 2 Rly. 3 Rly. 4 Rly. 5 Rly. 6 Rly. 7 Rly. 8 Rly. 9
461 493 525 557 589 621 653 685 717
Alarm High Set point Floating Pt.
462 494 526 558 590 622 654 686 718
463 495 527 559 591 623 655 687 719
Alarm Low Set Point Floating Pt.
464 496 528 560 592 624 656 688 720
465 497 529 561 593 625 657 689 721
Alarm K Factor Floating Pt.
466 498 530 562 594 626 658 690 722
467 499 531 563 595 627 659 691 723
Alarm Diff-Pressure Floating Pt.
468 500 532 564 596 628 660 692 724
469 501 533 565 597 629 661 693 725
Relay ON Time Floating Pt.
470 502 534 566 598 630 662 694 726
471 503 535 567 599 631 663 695 727
Relay Cycles Floating Pt.
472 504 536 568 600 632 664 696 728
473 505 537 569 601 633 665 697 729 Delay On Time Byte
474 506 538 570 602 634 666 698 730 Delay Off Time Byte
475 507 539 571 603 635 667 699 731 Pulse On Time Byte
476 508 540 572 604 636 668 700 732 Pulse Off Time Byte
477 509 541 573 605 637 669 701 733 After Flow Time Byte
478 510 542 574 606 638 670 702 734 Alarm Type Byte
479 511 543 575 607 639 671 703 735 Alarm Ch. Byte
480 512 544 576 608 640 672 704 736 Alarm Sec. Ch. Byte
481 513 545 577 609 641 673 705 737 Alarm Dig. Ch. Byte
482 514 546 578 610 642 674 706 738 Alarm ON/OFF Flag Byte
483 515 547 579 611 643 675 707 739 Relay State Flag Byte
484 516 548 580 612 644 676 708 740 Relay Assign Flag Byte
485 517 549 581 613 645 677 709 741
Alarm PWM Output Floating Pt.
486 518 550 582 614 646 678 710 742
487 519 551 583 615 647 679 711 743
Alarm PID Set Pt. Floating Pt.
488 520 552 584 616 648 680 712 744
489 521 553 585 617 649 681 713 745 Alarm PID KP Setting Integer
490 522 554 586 618 650 682 714 746 Alarm PID KI Setting Integer
491 523 555 587 619 651 683 715 747 Alarm PID I Band Integer
492 524 556 588 620 652 684 716 748 Alarm PID Direction Byte
1351 1361 1371 1381 1391 1401 1411 1421 1431
Override Value #1* Floating Pt.
1352 1362 1372 1382 1392 1402 1412 1422 1432
1353 1363 1373 1383 1393 1403 1413 1423 1433
Override Value #2* Floating Pt.
1354 1364 1374 1384 1394 1404 1414 1424 1434
1355 1365 1375 1385 1395 1405 1415 1425 1435
Override Value #3* Floating Pt.
1356 1366 1376 1386 1396 1406 1416 1426 1436
1357 1367 1377 1387 1397 1407 1417 1427 1437
Override Value #4* Floating Pt.
1358 1368 1378 1388 1398 1408 1418 1428 1438
1359 1369 1379 1389 1399 1409 1419 1429 1439 Override Mode* Byte
*Override Mode Byte Values: *Override Mode Programming:
Byte Value = 0: OFF (No overrides) Override Value #1 is the Set Point for Override.
Byte Value = 1: Input > SP with High Alarm Override Value #2 is the High Value Alarm Set Point.
Byte Value = 2: Input > SP with Low Alarm Override Value #3 is the Low Value Alarm Set Point.
Byte Value = 3: Input > SP with Alarm OFF Override Value #4 is N/A.
Byte Value = 4: Input < SP with High Alarm
Byte Value = 5: Input < SP with Low Alarm
Byte Value = 6: Input < SP with Alarm OFF