Ericsson LBI-39076B - Manual (Page 7)

REGULATORY COMPLIANCE LBI-39076B
7
REGULATORY COMPLIANCE
FEDERAL COMMUNICATIONS COMMISSION (FCC) REGULATIONS
1. This Telephone Interconnect, before its connection to a Telephone Central Office, must be reported to the
"CENTRALIZED OPERATIONS GROUP" of the local area Telephone Company (not the business office) by the
user, installer, or Installation Supervisor to ensure a smooth installation. The following three Central Office telephone
connection configurations are possible:
a. End-to-End configuration: The FCC registration number of this device (AXAUSA-21009-OT-E), ringer
equivalence number (0.4B), and connection jack (RJ-11) must be reported.
b. Four-Wire E&M configuration: The FCC registration number of this device (AXAUSA-21009-OT-E), ringer
equivalence number (0.0B), service order code (9.0Y & AS.3), facility interface code (TL11M telco end, TL11E
Ericsson GE end), and connection jack (RJ2GX) must be reported.
c. DID configuration: The FCC registration number of this system (AXAUSA-21009-OT-E), ringer equivalence
number (0.0B), service order code (9.0Y & AS.3), facility interface code (02RV2-T), and connection jack (RJ11)
must be reported.
2. This Telephone Interconnect, before its connection to a Telephone Private Branch Exchange (PBX), must be
reported to the "MAINTENANCE GROUP" of the local area Telephone Supplier by the user, installer, or Installation
Supervisor to ensure a smooth installation. The following four Private Branch Exchange telephone connection
configurations are possible:
a. End-to-End Loop Start configuration: The FCC registration number of this device (AXAUSA-21009-OT-E),
ringer equivalence number (0.4B), service order code (9.0Y), facility interface code (02LS2), and connection jack
(RJ-11) must be reported.
b. End-to-End Ground Start configuration: The FCC registration number of this device (AXAUSA-21009-OT-E),
service order code (9.0Y), facility interface code (02GS2), ringer equivalence number (0.0B), and connection jack
(RJ-11) must be reported.
c. Four-wire E & M trunk configuration: The FCC registration number of this device (AXAUSA-21009-OT-E),
ringer equivalence number (0.0B), service order code (9.0Y & AS.3), facility interface code (TL11M telco end and
TL11E Ericsson GE end), and connection jack (RJ2GX) must be reported.
d. DID (tie-trunk) configuration: The FCC registration number of this system (AXAUSA-21009-OT-E), ringer
equivalence number (0.0B), service order code (9.0Y & AS.3), facility interface code (02RV2-T), and connection
jack (RJ11) must be reported.
3. The total of all ringer equivalence numbers on any one line should not exceed 5.0 for best performance.
4. This device complies with Part 15 of FCC Rules. Operation of this device is subject to the following two conditions:
a. Device must not cause harmful interference.
b. Device must accept any interference, including interference that may cause undesired operation.
5. This device must not be installed on coin-operated or multi-party telephone lines.
6. DID answer supervision: Allowing this equipment to be operated in such a manner as to not provide for proper
answer supervision on DID calls is a violation of Part 68 of FCC rules.
7. E&M answer supervision: Allowing this equipment to be operated in such a manner as to not provide for proper
answer supervision on E&M calls is a violation of Part 68 of FCC rules.
8. Answer supervision will be returned within 500 ms after any of the following three conditions:
a. Incoming call is answered by the called station.