Yaskawa J7 to J1000 - Manual (Page 17)

(Header Title) Application Note
Doc#: PL.J1000.01 Copyright Yaskawa Electric America, Inc.©2008 www.yaskawa.com August 1, 2008 17 of 19
Subject: Transition Guide Product: J1000 Document: PL.J1000.01
Title: Product Transition Guide – J7 to J1000
Product Transition Guide – J7 to J1000
J7 J1000 Drive
Function
/ Parameter
Parameter
No.
Initial
Value
Parameter
No.
Initial
Value
Comments
Over Torque Detection
Level
n60 160% L6-02 150% —
Over Torque Detection
Time
n61 0.1 s L6-03 0.1 s —
Frequency Reference
Hole Selection
(Up / Down Function)
n62 0 d4-01 0
J7 J1000
n62 Æ 0 d4-01 Æ 0
n62 Æ 1 d4-01 Æ 1
Torque Compensation
Gain
n63 1.0 C4-01 1.00 —
Motor Rated Slip n64 — E2-02 — Default value depends on the drive capacity.
Motor No-Load Current
n65 — E2-03 —
Default value depends on the drive capacity.
Set E2-03 = n32* n65 / 100%
Slip Compensation Gain n66 0.0 C3-01 0.0 —
Slip Compensation
Time Constant
n67 2.0 s C3-02 2000 ms
J7: Setting unit is 1.0 s
J1000: Setting unit is 1 ms
MEMOBUS / Modbus
Communication Error
Behavior Selection
n68 0
H5-04
H5-05
3 —
MEMOBUS / Modbus
Communication Error
Detection
— — H5-05 1
J1000 J7
H5-04 H5-05
n68 Æ 0 1
n68 Æ 1 0 (C1-02)
n68 Æ 2 2 (C1-09)
n68 Æ 3 3
1
n68 Æ 4 No effect 0
MEMOBUS / Modbus
Frequency Reference
and Monitor Units
n69 0 H5-13 0
J7 J1000
n69 Æ 0 H5-13 Æ 0
n69 Æ 1 H5-13 Æ 1 and
o1-03 Æ 0
n69 Æ 2 H5-13 Æ 2
n69 Æ 3 H5-13 Æ 3
MEMOBUS / Modbus
Slave Address
n70 0 H5-01 1F
J7: Set as decimal value.
J1000: Set as hexadecimal value.
MEMOBUS / Modbus
Communication Speed
Selection
n71 2 H5-02 3
J7 J1000
n71 Æ 0 H5-02 Æ 1
n71 Æ 1 H5-02 Æ 2
n71 Æ 2 H5-02 Æ 3
n71 Æ 3 H5-02 Æ 4
MEMOBUS / Modbus
Parity Selection
n72 0 H5-03 0
J7 J1000
n72 Æ 0 H5-03 Æ 1
n72 Æ 1 H5-03 Æ 2
n72 Æ 2 H5-03 Æ 0
Transmission Wait Time n73 10 ms H5-06 10 ms —