Yaskawa J7 to J1000 - Manual (Page 13)

(Header Title) Application Note
Doc#: PL.J1000.01 Copyright Yaskawa Electric America, Inc.©2008 www.yaskawa.com August 1, 2008 13 of 19
Subject: Transition Guide Product: J1000 Document: PL.J1000.01
Title: Product Transition Guide – J7 to J1000
Product Transition Guide – J7 to J1000
J7 J1000 Drive
Function
/ Parameter
Parameter
No.
Initial
Value
Parameter
No.
Initial
Value
Comments
Frequency Reference
from Operator ENTER
Key Selection
n08 0 o2-05 0
J7 J1000
n08 Æ 0 o2-05 Æ 0
n08 Æ 1 o2-05 Æ 1
Maximum Output
Frequency
n09 60.0 Hz E1-04 60.0 Hz —
Maximum Output
Voltage
n10 200.0V* E1-05 200 V* * Values for a 400 V class drive are double.
Base Frequency n11 60.0 Hz E1-06 60.0 Hz —
Middle Output
Frequency
n12 1.5 Hz E1-07 3.0 Hz —
Middle Output Voltage n13 12.0 V* E1-08 16.0 V* * Values for a 400 V class drive are double.
Minimum Output
Frequency
n14 1.5 Hz E1-09 1.5 Hz —
Minimum Output
Voltage
n15 12.0 V* E1-10 12.0 V* * Values for a 400 V class drive are double.
Acceleration Time 1 n16 10.0 s C1-01 10.0 s —
Deceleration Time 1 n17 10.0 s C1-02 10.0 s —
Acceleration Time 2 n18 10.0 s C1-03 10.0 s —
Deceleration Time 2 n19 10.0 s C1-04 10.0 s —
S –Curve at
Acceleration Start
C2-01
S-Curve at Acceleration
End
C2-02
S-Curve at Deceleration
Start
C2-03
0.2 s
S-Curve at Deceleration
End
n20 0 (0 s)
C2-04 0.0 s
J7:
Selection parameter (setting 0, 1, 2 and 3).
Same setting for all conditions.
J1000:
Numerical parameter (time must be set in
seconds). The S-Curve is set separately for
each accel / decel profile selection.
Multiple Speed Ref. 1 n21 6.00 Hz d1-01 0.00 Hz —
Multiple Speed Ref. 2 n22 0.00 Hz d1-02 0.00 Hz —
Multiple Speed Ref. 3 n23 0.00 Hz d1-03 0.00 Hz —
Multiple Speed Ref. 4 n24 0.00 Hz d1-04 0.00 Hz —
Multiple Speed Ref. 5 n25 0.00 Hz d1-05 0.00 Hz —
Multiple Speed Ref. 6 n26 0.00 Hz d1-06 0.00 Hz —
Multiple Speed Ref. 7 n27 0.00 Hz d1-07 0.00 Hz —
Multiple Speed Ref. 8 n28 0.00 Hz d1-08 0.00 Hz —
Jog Frequency n29 6.00 Hz d1-17 6.00 Hz —
Frequency Reference
Upper Limit
n30 100% d2-01 100% —
Frequency Reference
Lower Limit
n31 0% d2-02 0.0% —
Motor Rated Current n32 — E2-01 — Depends on the drive capacity.
Motor Overheat
Protection
n33 0 L1-01 1
J7 J1000
n33 Æ 0 L1-01 Æ 1
n33 Æ 1 L1-01 Æ 2
n33 Æ 2 L1-01 Æ 0