Yaskawa V74X Drives - Manual (Page 28)

Conformance to
European EMC Directive
Section 6
In order to conform to EMC standards, the following methods are required for line filter application, cable shielding and Drive
installation.
The line filter and Drive must be mounted on the same metal plate. The filter should be mounted as close to the Drive as
practical. The cable must be kept as short as possible and the metal plate should be securely grounded. The ground of the
line filter and the Drive must be bonded to the metal plate with as much bare-metal contact as possible.
For main circuit input cables, a screened cable is recommended within the panel and is also suggested for external connec-
tions. The screen of the cable should be connected to a solid ground. For the motor cables, a screened cable (max. 20 m)
must be used and the screen of the motor cable should be connected to ground at both ends by a short connection, again
using as much bare-metal contact as practical.
Table 1-4 and Figure 1-4 show the line filter list for EMC standards and the installation/wiring of the Drive and line filter. For a
more detailed explanation, refer to document “Installation Guidelines for EMC Directive Using AC Drive Products.”
Table 1-4. Line Filters for EMC Standards
Model Line Filter
CIMR- Part Number Rated Weight Dimensions in in. (mm) Mounting Dim. in in. (mm) Screw
V7* MV FIL00 Current (A) lbs. (kg) H x W x D (1) H1 x W1 Size
20P1 A001
20P2 A002
20P4 A003
1083 10 1.8 (0.8) 7.6 x 3.2 x 2.0 (194 x 82 x 50) 7.1 x 2.4 (181 x 62) M5
20P7 A005
21P5 A008
1084 16 2.2 (1.0) 6.7 x 4.4 x 2.0 (169 x 111 x 50) 6.1 x 3.6 (156 x 91) M5
22P2 A011
23P7 A017 1085 26 2.4 (1.1) 6.9 x 5.7 x 2.0 (174 x 144 x 50) 6.3 x 4.7 (161 x 120) M5
25P5 A025
1100 50 5.1 (2.3) 12.0 x 7.2 x 2.2 (304 x 184 x 56) 11.3 x 5.9 (288 x 150) M6
27P5 A033
40P2 B001
1086 5 2.2 (1.0) 6.7 x 4.4 x 1.8 (169 x 111 x 45) 6.1 x 3.6 (156 x 91) M5
40P4 B002
40P7 B003
1087 10 2.2 (1.0) 6.7 x 4.4 x 1.8 (169 x 111 x 45) 6.1 x 3.6 (156 x 91) M5 41P5 B005
42P2 —
43P7 B009 1088 15 2.4 (1.1) 6.9 x 5.7 x 2.0 (174 x 144 x 50) 6.3 x 4.7 (161 x 120) M5
45P5 B015
47P5 —
1101 30 5.1 (2.3) 12.0 x 7.2 x 2.2 (304 x 184 x 56) 11.3 x 5.9 (288 x 150) M6
(1) D is the distance the filter will extend outward from the surface of the metal plate.
28
IG.V7.01_new format.qxd:IG.V7.01_new format.qxd 8/21/07 2:24 PM Page 28