Verilink PRISM 4151 (34-00258) Product Manual - Manual (Page 7)

General 1-3 PRISM 4151
This equipment complies with Part 68 of the FCC Rules. On
the rear or bottom of the CSU/DSU is a label that contains
the FCC registration number and other information. If
requested, provide this information to the telephone com-
pany.
1. All direct connections to DDS lines must be made using
standard plugs and jacks (compliant with Part 68). Table
1-A presents a list of applicable registration jack USOCs,
facility interface codes (FIC), and service order codes
(SOC). These are required when ordering service from
the telco.
2. If the CSU/DSU appears to be malfunctioning, it should
be disconnected from the DDS lines until the source of
trouble is determined to be your equipment or the tele-
phone line. If your equipment needs repair, it should not
be reconnected until it is repaired.
3. The CSU/DSU has been designed to prevent harm to the
DDS network. If the telephone company finds that the
equipment is exceeding tolerable parameters, it can tem-
porarily disconnect service. In this case, the telephone
company will give you advance notice, if possible.
4. Under FCC rules, no customer is authorized to repair this
equipment, regardless of warranty status.
5. If the telephone company alters its equipment in a man-
ner that will affect the use of this device, it must give you
advance warning so that you can have the opportunity for
uninterrupted service. You will be advised of your right
to file a complaint with the FCC.
6. In the event of equipment malfunction, all repairs should
be performed by our company or an authorized agent. It
is the responsibility of users requiring service to report
the need for service to our company or to one of our
authorized agents.
Canadian Emissions
Requirements
This digital apparatus does not exceed the Class A limits for
radio noise emissions from digital apparatus set out in the
Radio Interference Regulations of the Canadian Department
of Communications.
For the DC powered units only, end users should
use existing battery sources or a CSA certified
power supply.
Le present appareil numerique n’emet pas de bruits radio-
electriques depassant les limites applicables aux appareils
numeriques (de la class A) prescrites dans le Reglement sur
le brouillage radioelectrique edicte par le ministere des
Communications du Canada.
Warranty
TxPORT warrants each unit against defects in material and
workmanship for a period of five years from the date the
CSU/DSU was shipped to the customer. If the CSU/DSU
malfunctions at any time during the warranty period,
TxPORT will repair, or at TxPORT’s option, replace the
CSU/DSU free of charge.
The remedies listed herein are the users sole and exclusive
remedies. TxPORT shall not be liable for any indirect, direct,
incidental or consequential damages. The owner must return
the CSU/DSU to the factory, shipping prepaid and packaged
to the best commercial standard for electronic equipment.
TxPORT will pay shipping charges for delivery on return.
The customer is responsible for mode and cost of shipment
to TxPORT. This warranty does not apply if the CSU/DSU
has been damaged by accident, misuse or as a result of ser-
vice or modification by other than TxPORT personnel.
Ordering Information
Each PRISM 4151 unit is supplied with a reference manual
and is equipped with a V.35 data port (F-4151-001-1110 is
the default part number). Also provided is an 8-pin modular
to 8-pin modular (four twisted pairs) network cable (P/N 9-
1001 -004-010). Table 1-B displays the unit ordering num-
bers and options.
The optional Ethernet or Token Ring LAN interface cards
may be factory or customer installed.
The following optional equipment may also be needed for
the operation of the CSU/DSU.
Table 1-A USOC FIC
Port ID REN/SOC FIC USOC
56 kbps
64 kbps 6.0F 04DU5-56
04DU5-64 RJ-48S
Table 1-B Unit Ordering Numbers
Part Number Options
F-4151-001--111C
0
1
2
SNMP
SLIP
Ethernet
Token Ring
F-4151-100--111 Single Ethernet Card
F-4151-200--111 Single Token Ring Card