Verilink PRISM 4151 (34-00258) Product Manual - Manual (Page 6)

1-2 General PRISM 4151
• Flash memory allows field software upgrades
Specifications
Network Interface
Service Types: DDS I or DDS II clear channel con-
forming to TR62310
Operating Modes: Full duplex, point-to-point, multi-point
Line Rates: 56 and 72 kbps
Loop Range: Up to 45 dB of loss
Line Connection: RJ-48C jack, 8-pin modular
Timing Source: Network, DTE, Internal
Equipment Interface
Data Rates: Synchronous 56 and 64 kbps
Antistream Timer: Off, 10, 30, or 60 seconds
DTE Clocking: Internal or External
DTE Connection: 34-pin V.35 (CCITT)
Diagnostics
Loopbacks: V.54 (receive and send), alternating
loop, latching loop
BERT: 511 pattern
Management Interfaces
SUPV P ORT (S UPERVISORY )
Connection: 8-pin modular (RS-232)
Data Rates: 19.2 kbps
SLIP P ORT (S INGLE L INE I NTERNET P ROTOCOL )
Connection: 8-pin modular (RS-232)
Data Rates: 1.2, 2.4, 9.6, & 19.2 kbps
SNMP/TELNET/Ethernet ( OPTIONAL )
Connection: 8-pin modular
Network Protocol: TCP/IP based networks
Data Rate: 10 Mbps
Compatibility: 10BASE-T, ISO/IEC 8802-3
SNMP/TELNET/Token Ring ( OPTIONAL )
Connection: 8-pin modular
Network Protocol: TCP/IP based networks
Data Rate: 4 and 16 Mbps
Compatibility: Type 3 UTP, ISO/IEC 8802-5
Power
110 VAC: 100 mA, 12 W, 30 BTU maximum
Mechanical
Housing: Plastic standalone case
Mounting: Desktop or horizontal rack
Dimensions: 12 inches (30.40 cm) Wide
2 inches (5.08 cm) High
9 inches (22.86 cm) Deep
Environmental
Operating Temp: 32
°
to 122
°
F (0
°
to 50
°
C)
Storage Temp: -4
°
to 185
°
F (-20
°
to 85
°
C)
Humidity: 95% Maximum (Non-Condensing)
Compatibility
TR62310: November 1987
TR62310A: December 1989 (addendum 3)
TR41450: November 1981
Internet Standards: RFC 1157 (SNMP)
RFC 1155 (SMI)
RFC 1213 (MIB -II)
RFC 1055 (SLIP)
Enterprise TxPORT MIB
Enterprise DDS MIB
MIB-II: Device identification and interface
performance data. All applicable
objects and reporting traps maintained.
Industry Listings
FCC Compliance: Part 15 Class A, Subpart B, Part 68
U.S. Safety: UL 1459
Canadian Safety: CSA C22.2 No. 225-M90
Industry Canada: CS03, Issue 8
FCC Requirements
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15 of
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment
is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and
if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communi-
cations. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user is
required to correct the interference at his own expense. This
device must also accept any interference received, including
interference that may cause undesired operation. Shielded
cables must be used to ensure compliance with the Class A
FCC limits.
Changes or modifications to this
unit not expressly approved by the
party responsible for compliance could
void the user’s authority to operate the
equipment.