OpenEye CM-150 - Manual (Page 2)

Template
Quick Install Adaptor
2. Mount the Dome Enclosure
Locking Arms
Install Quick Install Adaptor on indoor ceiling
A. Using the Base Mounting Holes:
B. Using the Quick Install Adaptor (Optional):
C. Mount on a Single Gang Box (US):
PULL
1. Prepare Surface for Installation
Pull the tab and remove the camera module
Tighten tamper-proof screw
Tamper-proof Screw
2
3
4
5
Dome Base
Camera Module
Camera Liner
Dome Cover
T2
1
ROTATE 360°
PAN 360°
TILT 90°
T1
T1
T1
T1
Installation
Use the supplied torx driver
and the tamper-proof screw to
secure the dome cover.
Replace the dome cover and rotate it clockwise.
Carefully fit the camera liner
over the camera until it
snaps in place. Do not
obstruct the camera lens.
Use the included template to mark and prepare the mounting area.
To mount the base, fist remove the camera module by gently
pulling down the tabs that hold the camera module in place (see
image right) and remove the camera module. To re-assemble the
camera, gently pull down the tabs and insert the camera module.
When mounting the dome on a ceiling or wall using screws, first
knock-out the screw holes that correspond to the template marks T1.
This can be done using a Phillips screwdriver.
Push the cables through the dome base and 3/4” rubber grommet.
Make sure the grommet is properly installed to prevent dust penetra-
tion. The cables may be routed through the mounting surface if an
appropriate hole is cut using the template markings T2. If using the
side knock-out, make sure the video cables are properly arranged in
the cable notch and exit the side knock-out without being crushed.
When mounting the dome on a ceiling using the quick
install adapter, use the template to cut a hole on the
T2 markings.
Insert the adapter into the hole and use the screws to
adjust the position of the two locking arms on the
adapter, securing it to the mounting surface.
Push the cables through
the 1/2” rubber grommet
and the adapter. Make
sure the grommet is
properly installed on the
quick install adapter to
prevent dust penetration.
When mounting the camera to a single gang box, carefully remove the
screws from the gang box. Insert the 3/4” rubber grommet into the
camera base to prevent dust penetration, then push the cables through
the dome base and rubber grommet.
Mount the camera base on the gang box using the two screws
removed previously. Tighten the screws to secure the base.
Removing the dome cover and camera liner
Gently turn the dome cover counter-clockwise to unlock and remove
from the dome base. Remove the camera liner by gently pulling the
liner free of the four notches in the camera base.
Opening a side knock-out
Open a side knock-out on the dome base to the size
required to allow cable entry.
Use the base mounting holes to install the dome base
to a wall or ceiling with screws.
Note: When using the Quick Install Adapter, re-
assemble the dome and mount the whole camera
dome onto the adapter.
Push the video power cables through the opening
Feed the pre-connected video power cables through
the appropriate opening. Make sure the cable is
properly positioned and exits out of the side knock-out
(if required).
Adjust the camera position
Adjust the camera position by rotating and panning the
camera module. The focus and range of the lens can
be adjusted on some models. See the Camera
Adjustments section.
Install the dome liner on the camera module
C
Video-Power Cables
B
Single Gang Box Dome Base
T1
T1
Mount on a pre-installed US Single Gang Box
3/4”
Rubber
Grommet
1/2” Rubber Grommet
Mount with the Quick Install Adaptor
Side
Knock-outs
Mounting Surface
Mount with the Dome Base
Cable Notch
Cable Notch
3/4”
Rubber Grommet
A
Mounting Surface
6. Tighten the Tamper-
proof Screw
4. Install the Camera Liner
5. Replace the Dome Cover
3. Install Camera Module