OpenEye CM-512 Quick Start - Manual

This quick operation guide is a quick reference for users to install and operate the dome
camera and only provides basic information on the camera’s settings and operation. Before
attempting to connect, configure and operate the dome camera, please read the installation
guide and the user manual thoroughly.
Box Contents
Dome Switch Definition
1 Alarm Inputs
2 BNC Output
3 Console Connector
(Reserved)
4 Communication Switch
5 Camera ID Setting
6 RS-485 Connector
7 Protocol Settings
8 Power Connector
Communication Switch Setting
The table below shows the function of each switch within the Communication Switch on the
dome back plate.
Dome Control Protocol Setting
Refer to the table below and select a protocol and baud rate appropriate for your installation,
based on the control device. Adjust the Protocol Switch on the dome camera back plate. For
example, the protocol switch should be set as shown if you are using the Pelco D protocol,
with the switch number of 01 and a baud rate of 2400. For more switch configurtion details,
refer to the user manual
RS-485 Connector
The dome camera uses the RS-485 interface to communicate with a connected control device.
Connect a control keyboard to the speed dome using the terminal block. OpenEye recom-
mends using CAT 5 cables for RS-485 communication with a maximum length of 4000 feet
(1219 meters) for 24-gauge wire. If the total cable length exceeds 4000 feet, use a repeater to
maintain the signals. Refer to the table below for pin definition and wiring.
Pin Definition
1 R-
2 GND
3 R+
4 T-
5 T+
Power Connector
Refer to the this diagram for power connector definition before wiring.
Apply Alarm I/O
The CM-512 supports 4 digital alarm inputs and 2 digital alarm outputs. Please make sure
the alarm connections are properly wired before starting to configure alarm-related settings.
Please refer to this pin definition table for alarm system wiring.
Power Wire Length Specifications
CM-512 | High Speed Dome Camera Quick Guide
www.openeye.net
Wire Gauge Maximum Distance
22 27 feet
20 44 feet
18 69 feet
16 110 feet
Wire Gauge Maximum Distance
14 175 feet
12 279 feet
10 444 feet
RS-485 Setting
Half-duplex Full-duplex
Communication Switch SW 1
RS-485 Setting
SW 2
SW 3
Termination
SW 4 Line Lock
SW 5 System Initialization
SW 6 Reserved
1 AC IN +
2 Frame GND
3 AC IN -
Pin Definition Pin Definition
1 Alarm Out NO1 7 Alarm Out COM 2
2 Alarm Out NC 1 8 GND
3 Alarm Out COM 1 9 Alarm In 4
4 GND 10 Alarm In 3
5 Alarm Out NO 2 11 Alarm In 2
6 Alarm Out NC 2 12 Alarm In 2
Camera ID Setting
Change the camera ID if there is more than one camera on the same installation. The camera
ID is set using the camera ID switch on the back plate of the camera. For switch configuration
details, please refer to the user manual.
Note: No two cameras should have the same
camera ID, or a communication conflict
may occur.
Optical Cover CM-816 Camera Screws
Quick Start Guide User Manual Waterproof Gasket
Installation Manual Lubricant
Protocol Baud
Rate
Setting
Switch Setting
1
2 3 4 5 6
VCL 9600 OFF OFF OFF OFF OFF OFF
Pelco-D 2400 ON OFF OFF OFF OFF OFF
Pelco-P 4800 OFF ON OFF OFF OFF OFF
Chiper 9600 OFF OFF ON OFF OFF OFF
Philips 9600 ON OFF ON OFF OFF OFF
OPTIX-3 9600 ON ON ON OFF OFF OFF
AD422 4800 OFF OFF OFF ON OFF OFF
DP-P 9600 ON OFF OFF ON OFF OFF
Pelco-D 4800 ON ON OFF ON OFF OFF
Pelco-D 9600 OFF OFF ON ON OFF OFF
Pelco-P 2400 ON OFF ON ON OFF OFF
Pelco-P 9600 OFF ON ON ON OFF OFF
JVC 9600 ON ON ON ON OFF OFF
Kalatel-485 9600 ON OFF ON OFF ON OFF
Kalatel-422 4800 OFF ON ON OFF ON OFF