OpenEye CM-P307 - Manual (Page 2)

Function Setting
1. Push the lever to access the menu and confirm selec-
tion. Push the lever for one second to open or close the
menu. Use the lever to return to the previous menu from
motion detection or privacy mask setting sections.
2. Push the lever up to move the cursor up.
3. Push the lever down to move the cursor down.
4. Push the lever left to move the cursor left.
5. Push the lever right to move the cursor right.
6. Plug a test monitor into the optional EXT-VIDEO termi-
nal to view menu screens during installation.
7. Adjust the LED light level with the screw.
Camera Installation
1.
Use the supplied screws to mount the camera on a wall
or ceiling.
Installation
Adjusting the Camera Angle
1. To adjust the pan, the camera fixture left or right within a
range of -160º ~ 190º.
2. To adjust the tilt, grasp the LED cover and adjust the
direction up or down within a range of 6º ~ 90º.
3. To adjust the vertical orientation, rotate the camera
holder within a range of -178º ~ 178º.
2. If your camera uses a varifo-
cal lense, adjust the lens
by opening the LED cover.
Turn the Tele-Wide knob to
adjust the field of view. Turn
the Near-Far knob to set the
focus.
3. Once the camera is mounted
to the desired surface and is
focused correctly, re-assemble
the camera housing.
Using a Pole Mount
1.
Remove the screw on the bottom of the camera hous-
ing.
2. Open the dome cover.
3. Remove the tap cover and insert cables.
4. Apply teflon tape to the threaded portion of the pole
mount. (Use of teflon tape is necessary for water resis-
tence in outdoor applications).
5. Screw the pole mount into the base of the camera.
Camera OSD Menu
EXPOSURE
LENS
SELECT
MANUAL BRIGHTNESS 0 ~ 99
E. SHUTTER AUTO, 1/60 ~
1/100000
DC BRIGHTNESS 0 ~ 99
E. SHUTTER AUTO, 1/60 ~
1/100000
AGC OFF, LOW, MIDDLE, HIGH Auto Day/Night is
disabled if AGC is
OFF
SENSE-
UP
AUTO, OFF, X2, X4, X8, X16,
X32, X64, X128, X256, X512,
X1024
Use sense-up in low
light environments
BACK-
LIGHT
BLC BLC LEVEL OFF, LOW, MID,
HIGH
TOP 0 ~ 15:
BOTTOM 0 ~ 16
LEFT 0 ~ 15
RIGHT 0 ~ 16
HLC HBLC OFF
MANUAL HBLC LEVEL:
OFF,LOW, MID, HIGH
TOP, BOTTOM, LEFT, RIGHT
same as BLC
MODE ALL DAY, NIGHT
HLC LEVEL 1 ~ 100
MASK 1-4 ON
TOP: 0 ~ 33
BOTTOM: 1 ~ 34
LEFT: 0 ~ 44
RIGHT 1 ~ 45
OFF: HLC MASK
OFF
D-WDR SET LEVEL 0 ~ 20
3D-DNR OFF, LOW, MID, HIGH, AUTO Reduce noise in low
light environments
WHITE BALANCE
AWB
MODE
ATW Color temp. 2500 ~ 9500 K
MANUAL M-WR 0 ~ 128: Adjust the
red value
M-WB 0 ~ 128: Adjust the
blue value
PUSH Optimize white balance for current condi-
tions
R-Y GAIN 0 ~ 255 Adjust red tone of image
B-Y GAIN 0 ~ 255 Adjust blue tone of image
DAY & NIGHT
D&N
MODE
AUTO DAY-NIGHT 7 ~ 30
NIGHT-DAY 6 ~ 29
DELAY TIME 0 ~ 15: Set the
duration
AUTO-
CDS
A. DAY-NIGHT 6 ~ 36
A. NIGHT-DAY 6 ~ 36
C. DAY-NIGHT 0 ~ 255
C. NIGHT-DAY 0 ~ 255
COLOR Fixed at Color
B&W Fixed at B&W
EXT DELAY TIME 0 ~ 15
BURST ON, OFF Enable/disable burst
signal in BW mode
C-SUP 0 ~ 100 Color suppress
control
A-SUP 0 ~ 100 Iris suppress control
SMART
IR
ON, OFF Decreases screen
saturation of objects
within a short range
MIRROR MIRROR, OFF Vertical image
inversion
SHARP-
NESS
0 ~ 30
GAMMA 0.45, 0.55, 0.65
USER GAMMA .20 ~ 1.00 by incre-
ments of .05
PRIVACY
MASK
1 ~ 8
OFF
ON DOT SEL L_TOP, L_BOT,
R_BOT, R_TOP:
Determines location
for Motion Detection
DOT XY ENTER SETTING:
Determines coor-
dinates
MOVE XY ENTER SETTING:
Determines coor-
dinates
COLOR Select mask color
SPECIAL
LANGUAGE Select language (9
available)
TITLE OFF-ON EDIT Display the camera
name on screen
RESET Camera name reset
POSITION Camera name
position
DPC OFF Deactivates Detect
Pixel Correction in
low illumination
AUTO WHITE THR 0 ~ 255: Set the
limited value of white
pixel correction
LUMA THR 0 ~ 255: Set the
limited value of white
pixel correction
RETURN Move back to previ-
ous menu.
FACTORY SET YES, NO Reset your camera
to factory default
conditon
EXIT
SAVE AND EXIT Save the value and
exit the menu
EXIT Escape the menu
without saving