OpenEye 960H IR - Manual (Page 2)

Function Setting
1. Push the lever to access the menu and confirm selec-
tion. Push the lever for one second to open or close the
menu. Use the lever to return to the previous menu from
motion detection or privacy mask setting sections.
2. Push the lever up to move the cursor up.
3. Push the lever down to move the cursor down.
4. Push the lever left to move the cursor left.
5. Push the lever right to move the cursor right.
6. Plug a test monitor into the optional EXT-VIDEO termi-
nal to view menu screens during installation.
7. Adjust the LED light level with the screw.
Camera Installation
1.
Use the supplied screws to mount the camera on a wall
or ceiling.
Installation
Adjusting the Camera Angle
1. To adjust the pan, the camera fixture left or right within a
range of -160º ~ 190º.
2. To adjust the tilt, grasp the LED cover and adjust the
direction up or down within a range of 6º ~ 90º.
3. To adjust the vertical orientation, rotate the camera
holder within a range of -178º ~ 178º.
2. If your camera uses a varifo-
cal lense, adjust the lens
by opening the LED cover.
Turn the Tele-Wide knob to
adjust the field of view. Turn
the Near-Far knob to set the
focus.
3. Once the camera is mounted
to the desired surface and is
focused correctly, re-assemble
the camera housing.
Using a Pole Mount
1.
Remove the screw on the bottom of the camera
housing.
2. Open the dome cover.
3. Remove the tap cover and insert cables.
4. Apply teflon tape to the threaded portion of the pole
mount. (Use of teflon tape is necessary for water
resistence in outdoor applications).
5. Screw the pole mount into the base of the camera.
**MOTION and RS-485 SETUP
are not supported by OpenEye
Camera OSD Menu
LENS
SELECT
MANUAL
DC
EXPO-
SURE
PRESETS *Preset mode for common application to
speed up installation
CUSTOM User setting value
INDOOR For indoor
WINDOW Maximizing WDR function
OUT-
DOOR
For outdoor
WDR LOW WDR allows you to
clearly view a subject that
is backlight with bright
light.
NORMAL
MEDIUM
HIGH
BLC OFF
ON
AGC CUSTOM
LOW (24)
MEDIUM
(30)
HIGH (36)
SENSE-
UP
Enable the SENSE-UP function and
select level
OFF
AUTO For use in low light
situations, between 2X
and 64X)
MANUAL Select between 2X and
64X
FLICKER-
LESS
OFF Optimized mode for
flicker. If CRR is selected,
AWC mode will not be
available in the White
Balance menu.
CRR
CRR2
WHITE
BALANCE
ATW Automatic White Balance
AWC Find optimal white bal-
ance with use of white
paper in field of view.
MANUAL R/B Adjust red or blue levels
KELVIN Adjust color temp.
DAY &
NIGHT
AUTO INPUT
DELAY
The camera automatically
detects light levels and
sets mode accordingly.
COLOR Image is always dis-
played in color
B/W Image is always dis-
played in black and white
IMAGE
ADJUST
GAMMA 25 ~ 45 ~
100
Default: 45
SHARP-
NESS
MIN ~
MAX
Default: MAX
COLOR
GAIN
-8 ~ 0 ~ 8 Default: 0
FLIP OFF
HORZ Horizontal flip
VERT Vertical flip
BOTH Horizontal and vertical flip
ZOOM ON Max 4X Zoom
OFF Normal Image (no zoom)
PAN, TILT: Zoomed
image can be moved
horizontally and vertically
MOTION** OFF No motion detection
ON AREA
SELECT
Select up to 4 motion
detection areas
AREA
1 ~ 4
• Adjust position and
size of motion detec-
tion area
• Press ENTER to
move the motion
area setting section.
Press ENTER again
to change the mask
color
• When mask is white,
you can move the
mask up, down, left,
and right
• When the mask is
green and red, you
can adjust the mask
size
• Press ENTER for
a few seconds to
escape
PRIVACY OFF No privacy mask function
ON MASK
1-12
• Configure up to 12
privacy masks
• Press SET to open
privacy mask settings.
Press SET again to
change the mask
color
• When mask is white,
black, or red, it can be
moved up, down, left,
and right
• When mask is blue,
you can adjust the
size
• Press SET for a few
seconds to escape
MASK
COLOR
Select the mask
color (WHITE, RED, OR
BLACK)
FUNC-
TION
SETUP
RS-485
SETUP**
CAMERA # ID setting for RS-485
communication (1 ~ 256)
CAMERA
ID SETUP
ID DIS-
PLAY
Display the camera ID on
the screen
CAMERA
ID
Change the camera ID
ID
POSITION
Select the position to
display the ID on the
screen
SYNC INT Internal sync with 12V
Power
LL External sync with 24V
AC power
V-PHASE Phase controllable at
24V AC