Marantz SR7005 - Manual (Page 61)

57
Basic version
Simple version
Information
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA
Advanced version
n HDMI control function (vpage 57)
n Sleep timer function (vpage 58)
n Adjusting the volume of the speakers (vpage 58)
n Operating a wireless LAN-compatible mobile
terminal to play music and still pictures (vpage 59)
n Web control function (vpage 60)
n Panel lock function (vpage 62)
n Various memory functions (vpage 62)
Playback (Basic operation) (vpage 26)
Selecting a listening mode (Surround mode)
(vpage 46)
Playback (Advanced operation)
Convenient functions
HDMI control function
When you make an HDMI connection with a TV or player compatible
with this unit and HDMI control functions, you can perform the
following operations by setting the HDMI control function of each
device.
n This unit power off can be linked to the TV power off
step.
n You can switch audio output devices with a TV
operation.
When you set “Output audio from amp” in the TV audio output
setup operation, you can switch the amp power on.
n You can adjust this unit volume in the TV volume
adjustment operation.
n You can switch this unit input sources through
linkage to TV input switching.
n When playing the player, this unit input source
switches to the source for that player.
NOTE
• The HDMI control function only supports the HDMI OUT 1 connector.
To use the HDMI control function, connect the television to the
HDMI OUT 1 connector.
• When “HDMI Control” is set to “ON”, it consumes more
standby power.
• The HDMI control function controls operations of a TV that is
compatible with the HDMI control function. Make sure that the TV
and HDMI are connected when you perform HDMI control.
• Some functions may not operate depending on the connected TV or
player. Check the user guide of each device for details beforehand.
• When “Power Off Control” on the menu is set to “OFF” (vpage 83),
this unit is not set to standby even if the connected device is in the
standby mode.
• When connection changes are implemented, such as adding
connections to HDMI devices, linked operations may be initialized.
In this case, you will need to reconfigure the settings.
• When “HDMI Control” is set to “ON”, it is not possible to assign an
HDMI connector to “TV” at “Input Assign” (vpage 71).
1 Set the HDMI output connector corresponding with
the HDMI control function.
Set “HDMI Control” (vpage 82) to “ON“.
2 Turn the power on for all the equipment connected
by HDMI cable.
3 Set the HDMI control function for all equipment
connected by HDMI cable.
• Please consult the operating instructions for the connected
equipment to check the settings.
• Carry out steps 2 and 3 should any of the equipment be unplugged.
4 Switch the television input to the HDMI input
connected to this unit.
5 Switch this unit input to the HDMI input source and
check if the picture from the player is ok.
6 When you turn the TV’s power to standby, check
that the power of this unit also goes to standby.
If the HDMI control function does not operate properly, check the
following points.
• Is the TV or player compatible with the HDMI control function?
• Is “HDMI Control” (vpage 82) set to “ON”?
• Is “Power Off Control” (vpage 83) set to “All” or “Video”?
• Are the HDMI control function settings of all equipment correct?
• Is the television connected to the HDMI OUT 1 connector?
NOTE
Should any of the operations below be performed, the interlocking
function may be reset, in which case, repeat steps 2 and 3.
• “Input Assign” – “HDMI” (vpage 71) setting has changed.
• “Monitor Out” (vpage 82) setting is changed.
• There is a change to the connection between the equipment and the
HDMI, or an increase in equipment.