Marantz SR7005 - Manual (Page 13)

9
Basic version
Advanced version
Information
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA
Simple version
Set up speakers (Audyssey® Auto Setup)
STEP 1
Preparation
• In STEP 3, you will perform measurements at
multiple positions (two to eight positions) other
than the main listening position.
• You can achieve a more effective correction of
distortion within the listening area by performing
measurements at multiple positions.
9 Move the setup microphone to
position 2, use ui to select
“Measure”, and then press ENTER .
The measurement of the second position
starts. Measurements can be made in up to
eight positions.
[3/6] STEP3 Measurement
Please place the mic-
rophone at ear height
at 2nd listening
position.
Start next measurement. Test Tone will start
AUTO SETUP
AUDYSSEY AUTO SETUP
ENTER Enter RETURN Cancel
Measure
Next Calculation
MultEQ XT
If you want to omit measurements from the next
position onward, select “Next 1 Calculation”.
(Go to STEP4 Calculation )
10 Repeat step 9, measuring positions 3
to 8.
When measurement of position 8 is
completed, a “Measurements finished.”
message is displayed.
[3/6] STEP3 Measurement
Measurements finished.
Proceed to Step 4 (Analyze)
AUTO SETUP
AUDYSSEY AUTO SETUP
ENTER Enter RETURN Cancel
Retry
Next Calculation
MultEQ XT
NOTE
If “Caution” is displayed:
Go to “Error messages” (vpage 11), check
any related items, and perform the necessary
procedures.
If the problem is resolved, return and restart
“Audyssey Auto Setup”.
When performing Audyssey Auto
Setup over again
Press ui to select “Retry”, and then press ENTER .
When measuring has stopped
Press RETURN , to the “Cancel Auto Setup?”
prompt is displayed.
Press
o to select “Yes”, then press ENTER .
Setting up the speakers again
Repeat the operation from step 4 of
STEP1 Preparation .
STEP 2
Speaker Detection
STEP 3
Measurement
• In STEP 2, you will perform measurements at the
main listening position.
• This step automatically checks the speaker
configuration and speaker size, and calculates the
channel level, distance, and crossover frequency.
It also corrects distortion in the listening area.
6 Select “Measure” and then press
ENTER .
When measuring begins, a test tone is
output from each speaker.
• Measurement requires several minutes.
7 The detected speakers are displayed.
[2/6] STEP2 Spkr Detect Check
Go to Step 3 (Measurement) after speaker check
Retry
Next Measurement
Front
Center
Subwoofer
Surround
S.Back
F.Height
F.Wide
Yes
Yes
Yes
Yes
2spkrs
No
No
AUTO SETUP
AUDYSSEY AUTO SETUP
ENTER Enter RETURN Cancel
MultEQ XT
NOTE
If a connected speaker is not displayed, the
speaker may not be connected correctly. Check
the speaker connection.
8
Use ui to select “Next 1
Measurement” and then press ENTER .
4 Connect the setup microphone to the
SETUP MIC jack of this unit.
[1/6] STEP1 Preparation
Connect the speakers
and place them accord-
ing to the recommenda-
tions in the manual.
Set the following
items if necessary.
Start Auto Setup
Amp Assign
Channel Select
Auto Setup Start
AUTO SETUP
AUDYSSEY AUTO SETUP MultEQ XT
ENTER Enter RETURN Cancel
When the setup microphone is
connected, the following screen is
displayed.
This screen provides the method for setting
up 7.1-channel playback using surround back
speakers. For the method of setting up speakers
other than the 7.1-channel system, select “Amp
Assign” and perform step 3 and 4 of “Set up
“Amp Assign”” (vpage 54).
If unused channels are set with “Channel
Select”, measuring time can be shortened. For
setting, perform steps 5 to 9 of “Set up “Channel
Select”” (vpage 54).
5
Use ui to select “Auto Setup Start”
and then press ENTER .
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Confirm the setting Return to previous menu