Greenheck Network Interface Controller (475262 IOM) (Pre May 2013) - Manual (Page 13)

13 Network Interface Controller for Tempered Air Products
Points List • Modbus / BACnet®
Type
Modbus-RTU/TCP/IP
Network Address: 1
BACnet IP/Ethernet BACnet MSTP
Device Instance: 77000(default)
Read
Write
Description
Address Address Name Units
Analog 40002 1 Outside_Air_Temp °F R Outdoor Air Temp (###.#°F)
Analog 40003 2 Supply_Air_Temp °F R Supply Air Temp (###.#°F)
Analog 40004 3 Cold_Coil_Leaving_Temp °F R Cold Coil Temp (###.#°F)
Analog 40005 4 Return_Air_Temp °F R Return AirTemp (###.#°F)
Analog 40006 5 Exhaust_Discharge_Temp °F R Exhaust Discharge Temp (###.#°F)
Analog 40007 6 OA_After_Wheel_Temp °F R Outdoor Air After Wheel Temp (###.#°F)
Analog 40011 10 Heat_Output percent R/W Heater output (0-100%)
Analog 40012 11 Cool_Output percent R/W Cooling output (0-100%)
Analog 40013 12 VFD_Supply_Output percent R/W VFD Supply Fan Output (0-100%)
Analog 40014 13 VFD_Exhaust_Output percent R/W VFD Exhaust Fan Output (0-100%)
Analog 40015 14 VFD_Wheel_Output percent R/W VFD Wheel Output (0-100%)
Analog 40016 15 RA_Damper_Output percent R/W Return Air Damper Output (0-100%)
Analog 40018 17 Supply_VFD_Mointor volts R Supply VFD Monitor Signal (Vdc)
Analog 40019 18 Exhaust_VFD_Monitor volts R Exhaust VFD Monitor Signal (Vdc)
Analog 40027 26 User_Define_B1_AI no-units R User Define B1 Analog Input
Analog 40028 27 User_Define_B2_AI no-units R User Define B2 Analog Input
Analog 40031 30 User_Define_Y4_AO no-units R/W User Define Y4 Analog Output
Integer 40216 1007 CO2_Level ppm R CO2 Levels (ppm)
Inactive_Text Active_Text
Digital 10011 10 Unit_Start_Stop Stop Start R/W Unit start/stop command
Digital 10012 11 Reset_Alarms Don't Reset Reset Alarms R/W Reset alarms command
Digital 10015 14 Cooling_Stg1_Command Off On R/W Cooling Stage 1 Command
Digital 10016 15 Cooling_Stg2_Command Off On R/W Cooling Stage 2 Command
Digital 10017 16 Heat_Stg1_Command Off On R/W Heating Stage 1 Command
Digital 10018 17 Occ_Unocc_Command Off On R/W Occupied/unoccupied Command
Digital 10019 18 Remote_Exh_Fan_Command Off On R/W Remote Exhaust Fan Command
Digital 10020 19 HGRH_Command Off On R/W Hot Gas Reheat Command
Digital 10021 20 Global_Alarm Off Alarm R Global alarm indication (active when there is at least one alarm)
Digital 10024 23 Fan_Proving_Status Off On R Fan Proving status
Digital 10026 25 Dirty_filter_Status Clean Dirty R Dirty filter status
Digital 10027 26 Wheel_Status Ok Not Ok R Wheel status-Not Ok=Wheel not running when commanded on
Digital 10028 27 Supply_air_low_limit Off Alarm R Supply air temperature low limit alarm
Digital 10029 28 Sensor_B1_out_of_range Off Alarm R Sensor B1 out of range
Digital 10030 29 Sensor_B2_out_of_range Off Alarm R Sensor B2 out of range
Digital 10031 30 Sensor_B3_out_of_range Off Alarm R Sensor B3 out of range
Digital 10032 31 Sensor_B4_out_of_range Off Alarm R Sensor B4 out of range
Digital 10033 32 Sensor_B5_out_of_range Off Alarm R Sensor B5 out of range
Digital 10034 33 Sensor_B6_out_of_range Off Alarm R Sensor B6 out of range
Digital 10039 38 User_Define_B5_DI Open Closed R User Define B5 Digital Input
Digital 10040 39 User_Define_B6_DI Open Closed R User Define B6 Digital Input
Digital 10041 40 User_Define_NO1_DO Off On R/W User Define NO1 Digital Output
Digital 10042 41 User_Define_NO2_DO Off On R/W User Define NO2 Digital Output
Digital 10043 42 User_Define_ID2_DI Open Closed R User Define ID2 Digital Input
®