Flowserve M-series PolyChem User Manual
Page 45
USER INSTRUCTIONS PolyChem M-SERIES ENGLISH 71569218 07-11
flowserve.com
Page 45 of 60
®
6.8.1
Wet End
a)
Inspect the bushings, thrust journals and shaft
for wear. Total diametrical and axial wear limits
are shown in Figure 6-30.
b)
Inspect the casing, impeller, holder, inner
magnet and containment shell for wear,
corrosion and defects. The nominal liner
thickness for all components is 3.18 mm (0.125
inches).
Figures 6-31 through 6-36 have been provided as a
guide for identifying the features listed in the table.
Figure 6-31: Shell
Figure 6-32: Shaft
Figure 6-33: Bushing
Figure 6-34: Inner Magnet
Figure 6-30: Wet end allowable wear
Axial Allowable Bearing Wear (total) 0.38 mm (0.015 in)
Diametrical Allowable Bearing Wear (total) 0.61 mm (0.024 in)
Liner Allowable Wear 25% of thickness
AS NEW DIMENSIONS – NOMIINAL
AXIAL BEARING FEATURES
Group A and 1
Group B and 2
Thrust Journal and Bushing
Thickness
4.78 (0.188)
6.35 (0.250)
Shell Thrust Bushing Depth
95.89 (3.775)
112.27 (4.420)
Shaft Shoulder Thickness
5.21 (0.205)
7.9 (0.31)
Pump Model
Impeller Height
Casing Depth
32-160
49.99 (1.968)
70.79 (2.787)
65-160
50.50 (1.988)
85.24 (3.356)
40-200
51.26 (2.018)
84.89 (3.342)
1.5x1-6
48.97 (1.928)
74.73 (2.942)
3x1.5-6
52.27 (2.058)
78.87 (3.105)
3x2-6
52.27 (2.058)
78.87 (3.105)
1.5x1-8
49.48 (1.948)
75.82 (2.985)
32-250
57.66 (2.270)
92.91 (3.658)
50-250
58.17 (2.290)
93.24 (3.671)
65-250
63.25 (2.490)
98.08 (3.862)
2x1-10
57.66 (2.270)
95.76 (3.770)
3x2-10
56.90 (2.240)
94.92 (3.737)
4x3-10
63.25 (2.490)
101.35 (3.990)
RADIAL BEARING FEATURES
Group A and 1
Group B and 2
Bushing Inside Diameter
38.13 (1.501)
50.04 (1.970)
Shaft Outside Diameter
38.087 (1.4995)
50.000 (1.9685)
ADDITIONAL COMPONENT FEATURES
Group A and 1
Group B and 2
Shell Inside Diameter
124.89 (4.917)
195.83 (7.71)
Inner Magnet
O.D.
121.92 (4.800)
190.04 (7.482)
I.D.
44.450 (1.7500)
50.533 (1.9895)
Width
12.75 (0.502)
12.75 (0.502)
Key Width
12.57 (0.495)
12.57 (0.495)
Note: Dimensions shown above are in millimeters (inches).
Bushing
I.D.
Thrust
Bearing
Depth
Inside
Diameter
Bushing
I.D.
Bearing
Holder
Shoulder Thickness
Outside
Diameter
Outside
Diameter
Width
Inside Diameter
Outside Diameter