Flowserve ESP3 - Manual (Page 39)

ESP3 USER INSTRUCTIONS ENGLISH 26999943 08-11
Page 39 of 64
Figure 6-1: Recommended spare parts
(Reference Figure 8-11)
Spare Parts Class
Part Number Description
1 2 3
2100 Pump shaft (see note 2) 1
2200 Impeller 1
2500 Throttle Bushing for cover 1 1
3020.1 Bearing -- intermediate Note1 Note1
3020.2 Bearing -- adapter (bottom) 1 1
3031 Thrust bearing 1 1
3110 Bearing body -- thrust bearing 1 1
3250 Bearing holder Note1 Note1
3400 Adjusting sleeve 1
4120.1 Gland 1 1
4130 Packing (optional) Note1 Note1 Note1
4134 Seal cage -- packed box 1 1
4200 Mechanical seal (optional) 1 1 1
4310.1 Klozure lip seal -- bearing body 1 1 1
4310.2 Klozure lip seal -- upper column 1 1 1
4590.1 Gasket -- casing 1 1 1
4590.2 Gasket -- Impeller 1 1 1
4590.3 Gasket -- discharge pipe to casing flange 1 1 1
4590.4 Gasket -- stuffing box to upper column 1 1 1
4590.5 Gasket -- mechanical seal (optional) 1 1 1
4590.6 Gasket -- column to mounting plate 1 1 1
4590.7 Gasket -- manifold to mounting plate 1 1
6531 Strainer 1
6700.2 Pump key 1
7200 Coupling 1
8000 Motor complete (see note 3) 1
Note 1: Check record card for quantity required.
Note 2: Check record card for length required.
Note 3: When ordering motor parts, give motor serial number and model number as read from the motor
nameplate. Also furnish pump serial number.
6.5 Fastener torques
Figure 6-2: Recommended bolt torques for lubricated or PTFE-coated fasteners
Item Description Group 1 Group 2 Group 3
[6570.2-.3] Column/column/adaptor cap screws and nuts ⅝ in. – 122 Nm (90 ft-lb) ⅝ in. – 122 Nm (90 ft-lb) ¾ in. – 210 Nm (155 ft-lb)
[6570.5] Discharge elbow/casing ½ in. – 61 Nm (45 ft-lb) ½ in. – 61 Nm (45 ft-lb) ⅝ in. – 122 Nm (90 ft-lb)
⅝ in. – 122 Nm (90 ft-lb) ⅝ in. – 122 Nm (90 ft-lb) ¾ in. – 210 Nm (155 ft-lb)
[6570.7] Manifold/mounting plate cap screws ½ in. – 61 Nm (45 ft-lb) ½ in. – 61 Nm (45 ft-lb) ½ in. – 61 Nm (45 ft-lb)
[6580.9] Bearing Body/column cap screws ⅜ in. – 24 Nm (18 ft-lb) ½ in. – 50 Nm (37 ft-lb) ½ in. – 50 Nm (37 ft-lb)
[6570.16] Cap screw cover/adapter (token bolts) ⅜ in. – 27 Nm (20 ft-lb) ⅜ in. – 27 Nm (20 ft-lb) ⅜ in. – 27 Nm (20 ft-lb)
½ in. – 54 Nm (40 ft-lb)
[6572.2] Gland packed box studs and nuts ⅜ in. – As required ½ in. – As required ½ in. – As required
[6572.3] Gland seal chamber studs and nuts ⅜ in. – 19 Nm (14 ft-lb) ½ in. – 41 Nm (30 ft-lb) ½ in. – 41 Nm (30 ft-lb)
[6579.*] Socket Head Cap screws – All locations ½ in. – 54 Nm (40 ft-lb) ½ in. – 54 Nm (40 ft-lb) ½ in. – 54 Nm (40 ft-lb)
Notes:
1. For non-lubricated/coated threads, add 25% to the values given above.
2. Gasket joint torque values are for unfilled PTFE gaskets. Other gasket materials may require additional torque to seal. Exceeding metal joint
torque values is not recommended
.