Basler Electric BE1-851E DNP3 Protocol - Manual (Page 34)

15. BF status is the bit mapped variable with format as described in Table 5-7. Delta of 1 deviation will
cause en event.
Table 5-7. Breaker Failure Status Format
Value / Bit Mask (hex) Description
0001 Breaker Operation Control State {1=Breaker Operation Enabled;
0= Breaker Operation Disabled}
0002 Breaker State {1=Breaker Opened; 0= Breaker Closed}
16. Delta of 1 bit (any change) will cause an event.
17. Read values for Hardware Output Control is 1 = Enabled, and 0=Disabled.
18. Read values for x43 AUX Virtual Switch Logic Mode are 0 for Disabled, 1 = ON/OFF PULSE, 2 =
ON/OFF, and 3= OFF/MOMENTARY ON.
19. Read values for Setting Group Mode is 0= Disabled, 1=discrete select, and 2= binary select.
Setting groups can be controlled via DNP object 12 if value is 1 or 2.
20. Read values for 101 Breaker Control Switch Mode is 0=Disabled and 1=Enabled.
21. Latched Targets Status format is described in Table 5-5 under Note 6 to Table 5-4. Delta of 1
deviation will cause an event. Latched Targets Status can be reset via object 41 point 7.
22. BE1-851E Relay System Status is represented as 4 part, 16-bit mapped variables. The four part
System Status is described in Table 5-8. (For more information, see the BE1-851E Instruction
Manual, Section 6, Reporting and Alarm Functions). Delta of 1 deviation will cause an event.
Table 5-8. System Status
Value/Bit Mask (hex) Part 1 Description Part 2 Description Part 3 Description Part 4 Description
0001h 50 Phase Tripped BF Picked Up Virtual Output A Input Contact 1
0002h 150 Phase Tripped 51 Phase Picked Up Virtual Output 1 Input Contact 2
0004h 50 Neutral Tripped 51 Neutral Picked UP Virtual Output 2 Input Contact 3
0008h 150 Neutral Tripped 51 Q Picked Up Virtual Output 3 Input Contact 4
0010h 50Q Tripped 62 Tripped Virtual Output 4 101 TRIP
0020h 150Q Tripped 162 Tripped Virtual Output 5 101 CLOSE
0040h. BF Tripped 43 Virtual Output 6 101 SLIP CONTACT
0080h 51 Phase Tripped 143 Virtual Output 7 HMI Reset Key
0100h 51 Neutral Tripped 243 Virtual Output 8 Logic Alarm
0200h 51 Q Tripped 343 Virtual Output 9 Major Alarm
0400h 50 Phase Picked Up 79 Close Virtual Output 10 Minor Alarm
0800h 150 Phase Picked Up 79 Enabled Virtual Output 11 Output 1 Trip Coil Monitor
1000h 50 Neutral Picked Up 79 Lockout Virtual Output 12 Setting Group 0
2000h 150 Neutral Picked Up 79 Reclose Fail Virtual Output 13 Setting Group 1
4000h 50Q Picked Up 79 Block Output Virtual Output 14 Setting Group 2
8000h 150Q Picked Up Always False (zero) Virtual Output 15 Setting Group 3
Analog Output Status Points and Control Blocks
Table 5-9 lists both the Analog Status Points (Object 40) and the Analog Output Control Blocks (Object
41). It is important to note that Analog Output Status Points are not included into Class 0.
The Return Status Value for object 41 for all control operations may be 6 (hardware problem) due to a
value out of range, or a relay internal state. One of the reasons for rejection may be if another
communication port or front panel HMI is actively programming. For more information, see the BE1-851E
Instructional Manual, Section 10, Human-Machine Interface.
5-14 BE1-851E DNP Protocol 9289900792 Rev C