Hardware specifications, Vtc 7100-d1k/ 7110-d1k/ 7120-d1k – NEXCOM VTC 7100-D1K User Manual
Page 17
Copyright © 2012 NEXCOM International Co., Ltd. All Rights Reserved.
3
Chapter 1: Product Introduction
VTC 71-D Series User Manual
Hardware Specifications
VTC 7100-D1K/ 7110-D1K/ 7120-D1K
CPU
▪ VTC7100 series: Intel
®
Atom™ D2550 1.86GHz
▪ VTC7110 series: Intel
®
Core™ i7 2610UE 1.5GHz
▪ VTC7120 series: Intel
®
Celeron
®
847E 1.1GHz
Main Chipset
▪ VTC7100 series: ICH10R
▪ VTC7110 series: QM67
▪ VTC7120 series: QM67
Memory
▪ VTC 7110 and VTC 7120 series: One 204-pin SO-DIMM DDR3 1333 up to 8GB
2GB (default)
▪ VTC 7100 series: One 204-pin SO-DIMM DDR3 1066 up to 4GB
2GB (default)
Expansion
▪ 1x Mini-PCIe socket (PCIe + USB) for WLAN option
▪ 1x Mini-PCIe socket (USB) for WWAN option
▪ 1x Bluetooth module for option
▪ 1x onboard uBlox NEO-6Q GPS module or optional GPS module with dead
reckoning
I/O Interface-Front
▪ 1x Line-out, 1x Mic-in (for WWAN CM8000 voice communication)
▪ 2x SIM card socket (selectable)
▪ 1x System reset button
▪ 1x USB 2.0 host type A connector
▪ 1x Power button
▪ 1x CFast with protection cover
▪ 1x Accessible 2.5” SATA II SSD tray
▪ 4x LED’s for power, storage, WLAN/ WWAN and GPIO
I/O Interface-Rear
▪ 1x 9~36VDC input with Ignition
▪ 1x 12V/4A DC output, SMBus
▪ 1x DB26 LVDS interface with 12V and USB2.0
▪ 1x DB15 VGA
▪ 1x DB9 RS-232 (default) or OBDII (optional)
▪ 1x DB9 RS-422/ 485
▪ 1x DB9 female connector for 4x DI and 4x DO
(Digital Input)
Input Voltage (Internal Type): 5VDC TTL (default)
Input Voltage (Source Type): 0~30 VDC
(Digital Output)
Digital Output (Sink Type): 5VDC TTL (default), max current: 20mA
Digital Output (Source Type): 0~30VDC, max current: 250mA
▪ 2x USB 2.0 host type A connector
▪ 2x RJ45 with LEDs for 10/ 100/ 1000Mbps Ethernet
▪ 10-Pin terminal block for 8x DI and 8x DO
Isolation: 5K Vrms
(Isoated Digital Input)
Input Voltage (Internal Type): 5VDC TTL (default)
Input Voltage (Source Type): 0~30 VDC
(Isoated Digital Output)
Digital Output (Sink Type): 5VDCTTL (default), max current: 20mA
Digital Output (Source Type): 0~30VDC, max current: 250mA
▪ 5-Pin terminal block for 3x analog input
Isolation: 2K Vrms
2x isolated analog voltage input 12VDC (Max.)
1x isolated analog current input 10A (Max.)
▪ 1x Line-out, 1x Mic-in
▪ 1x SMA-type GPS antenna connector
▪ 4x Antenna hole reserved for SMA-type antenna connector (WWAN/
WLAN/ BT)
▪ 1x DB9 male connector for 1x OBDII module (default) and 2x OBDII
module (optional)