Hardware specifications – NEXCOM NViS 3620 User Manual
Page 17
Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved.
3
Chapter 1: Product Introduction
NViS3620/3720 series User Manual
Hardware Specifications
CPU
▪ Intel
®
Core™ processor dual core i7-4650U, 1.7GHz
▪ Intel
®
Core™ processor dual core i5-4300U, 1.9GHz
Memory
▪ 2 channel 204-pin DDR3L SO-DMIM socket support 1333/1600MHz up to
16GB, default 4GB.
Storage
▪ 2x 2.5” SATA 3.0 SSD/HDD (externally accessible). RAID 0,1 supported.
Optional lockable storage available
▪ 1x CFast (externally accessible)
Expansion
▪ 1x full size Mini-PCIe socket (USB 2.0)
▪ 1x full size Mini-PCIe socket (USB 2.0 + PCIe)
▪ 1x full size Mini-PCIe socket (USB 2.0 + PCIe)
▪ 1x half size Mini-PCIe socket (USB 2.0 + PCIe)
Function
▪ 1x default U-blox UBX-G6010 GPS module (50-channel and GALILEO) or
optional modules with Dead Reckoning or GLONASS support
▪ Built-in G-sensor
I/O Interface-Front
▪ 4x LED for power, storage, WWAN, WLAN
▪ 2x externally accessible SATA 3.0 SSD/HDD tray, RFID 0, 1 supported
(optional lockable storage available)
▪ 1x dual USB type A connector for USB 3.0 port + USB 2.0 port
▪ 2x externally accessible SIM card socket (selectable)
▪ 1x phone jack 3.5mm for 1x Mic-In
▪ 1x phone jack 3.5mm for 1x Line-Out
▪ 1x externally accessible CFast card socket with cover
▪ 1x event button (trigger type)
▪ 1x reset button
▪ 3x antenna hole for WWAN/WLAN/BT
I/O Interface-Rear
▪ 1x 9~36VDC input with ignition and 36W typical power consumption
(NViS3620)
▪ 1x 9~36VDC input with ignition and 37W typical power consumption
(NViS3720)
▪ 1x dual USB type A connector for USB 3.0 port + USB 2.0 port
▪ 2x RJ45 10/100/1000 Fast Ethernet with LED
▪ 1x phone jack 3.5mm for 1x Mic-In
▪ 1x phone jack 3.5mm for 1x Line-Out with 1.5W output each
▪ 1x DB-15 VGA. Resolution up to 2560 x 1600 @60Hz
▪ 1x DP port. Resolution up to 2560 x 1600 @60Hz
▪ 2x DB-9 RS-232
▪ 1x DB-9 RS-232/422/485 (RI/5V/12V selectable)
▪ 1x DB-9 for CAN 2.0B (optional CAN Bus 2.0B Mini-PCIe card), 2x MCU-
DI and 2x MCU-DO
▪ 1x 16-pin terminal block
- 1x CAN Bus 2.0B (on board)
- 1x optional OBDII module (ASE J1939 or J1708)
- 8x programmable GPIO
(Digital Input)
Input voltage (internal type): 5VDC TTL (default)
Input voltage (source type): 3~12VDC
(Digital Output)
Digital Output (sink type): 5VDC TTL (default), max current: 20mA
Digital Output (source type): 3~24VDC, max current: 150mA