CONTA-CLIP CMS-BS 100 - Manual (Page 4)

CONTA-ELECTRONICS
CMS CMS CMS CMS----BS100 BS100 BS100 BS100
Multi Multi Multi Multi----function Multi function Multi function Multi function Multi----channel converter channel converter channel converter channel converter
Further information: www.conta-clip.com Cat. No.: 95120.1 Further information: www.conta-clip.com
Function: absolute differential Function: absolute differential Function: absolute differential Function: absolute differential
This lowest value is selected by setting the dipswitches as shown below.
DIP1 DIP1 DIP1 DIP1 DIP2 DIP2 DIP2 DIP2 DIP3 DIP3 DIP3 DIP3 DIP4 DIP4 DIP4 DIP4
off on on off
Select the input range:
input1 input1 input1 input1 input2 input2 input2 input2
DIP5 DIP5 DIP5 DIP5 DIP6 DIP6 DIP6 DIP6 DIP7 DIP7 DIP7 DIP7 DIP8 DIP8 DIP8 DIP8 value value value value
off off off off 0..10V / 0..20mA
Function: analog to digital differential Function: analog to digital differential Function: analog to digital differential Function: analog to digital differential
The absolute differential between input 1 and 2 and/or input 3 and 4 will be forwarded to resp.
output1 and output2.
This function is selected by setting the dipswitches as shown below.
DIP1 DIP1 DIP1 DIP1 DIP2 DIP2 DIP2 DIP2 DIP3 DIP3 DIP3 DIP3 DIP4 DIP4 DIP4 DIP4
off on off off
Select the input range:
input1 input1 input1 input1 input2 input2 input2 input2
DIP5 DIP5 DIP5 DIP5 DIP6 DIP6 DIP6 DIP6 DIP7 DIP7 DIP7 DIP7 DIP8 DIP8 DIP8 DIP8 value value value value
off off off off 0..10V / 0..20mA
Function: highest / lowest value Function: highest / lowest value Function: highest / lowest value Function: highest / lowest value
The highest / lowest value between input 1 and 2 and/or input 3 and 4 will be forwarded to
resp. output1 and output2.
This highest value is selected by setting the dipswitches as shown below.
D D D DIP1 IP1 IP1 IP1 DIP2 DIP2 DIP2 DIP2 DIP3 DIP3 DIP3 DIP3 DIP4 DIP4 DIP4 DIP4
off on off on
Digital output1 switches when input1 > input2, output2 switches when input3 > input4.
The difference between the inputs must be >1%.
This function is selected by setting the dipswitches as shown below.
DIP1 DIP1 DIP1 DIP1 DIP2 DIP2 DIP2 DIP2 DIP3 DIP3 DIP3 DIP3 DIP4 DIP4 DIP4 DIP4
off on on on
Select the input range:
input1 input1 input1 input1 input2 input2 input2 input2
DIP5 DIP5 DIP5 DIP5 DIP6 DIP6 DIP6 DIP6 DIP7 DIP7 DIP7 DIP7 DIP8 DIP8 DIP8 DIP8 value value value value
off off off off 0..10V / 0..20mA
off on off on NI1000
on off on off PT1000
Note: due to different resolutions this function cannot combine U/I in with RTD in. When
RTD is selected for input1/2, input3/4 must also be set as RTD.