CONTA-CLIP CMS-BS 100 - Manual

CONTA-ELECTRONICS
CMS CMS CMS CMS----BS100 BS100 BS100 BS100
Multi Multi Multi Multi----function Multi function Multi function Multi function Multi----channel converter channel converter channel converter channel converter
Further information: www.conta-clip.com Cat. No.: 95120.1 Further information: www.conta-clip.com
Electrical specifications Electrical specifications Electrical specifications Electrical specifications Manual Manual Manual Manual
The CMS-BS100 is a multi-functional signal converter with
multiple inputs and outputs. Analog voltage-, current-,
RTD- and digital signals can be converted to analog or
digital outputs. Several common conversion functions are
already included, e.g.
- analog inverter(s)
- 1 input to 2 separate outputs
- 2 inputs to 1 output (highest or lowest input)
- 2 inputs to 1 output (difference between inputs)
- RTD (Ni1000, PT1000) to analog output(s)
- Potentiometer(s) to analog output(s)
- up/down (2 digital inputs) to 1 analog output,
with selectable ramp from 5sec to 30min.
- if analog input1>2 then digital output1 on
if analog input3>4 then digital output2 on
- pulse stretcher(s)
Furthermore, this module is especially suited for customer-
specific applications. Due to its number of inputs and
outputs it can be programmed to measure the inputs and
control the outputs in any way or function the customer
desires.
Even for very low volumes, special programming can be
very interesting for you!
Order information Order information Order information Order information
type
cat.no
Input data Input data Input data Input data
4 Multifunctional analog/dig. Inputs
input resistance (U)
input resistance (I)
accuracy (U/I)
configuration resistor (PT/ NI1000)
RTD standard (PT1000 / NI1000)
accuracy (PT1000 / NI1000)
RTD current (PT1000 / NI1000)
digital input min puls width
digital input HI / LO status
Output data Output data Output data Output data
2 analog/dig. outputs
analog output
analog output load
offset U/I
digital output
digital output current
digital output voltage
General data General data General data General data
configuration information
power supply voltage
current consumption
conversion error
response time (analog / digital)
temperature coefficient
operating temperature range
CE marking
dimensions (l x w x h) on TS35x7,5
conductor cross section
connection system
insulation stripping length
40K2 Ohm
100 Ohm
10mV/20uA
CMS-BS100
15963.2
0..1V / 0..10V / 0(4)..20mA / RTD / 24VDC(14..30V)
input type is selected via jumpers
100mA continious collector current
5..40VDC
jumper selectable
output type is selected via jumpers
< 10mV / 20uA
Optocoupler transistor output
Resistor type: Plug-in(Rt) 18K2-0.1% (not included), Temp. range -20°C .. 140°C
0,5°C
0…10V DC or 0(4)..20mA, short-circuit and overvoltage (24Vac/dc) protected
U: > 1kOhm I: < 500Ohm
0.52mA
500us
>14VDC / <4VDC
EN60751/DIN 43760
CMS-BS100 manual
99 x 17,5 x 114,5mm
0,2 - 2,5 mm²
-20°C…50°C
Approx. 25mA
<1% FSR, <0.5% when calibrated on requested range(U, I or RTD)
10ms / 60us + minimal pulse width
< 0,02% /K
24V DC ±20%
7 mm
screw clamp
Low Voltage Directive (LVD) 2006/95/EC, according requirements of EN 50178
EMC Directive 2004/108/EC, according requirements of EN 55011 and EN 61326-1
Features:
• 4 Multifunctional analog/digital inputs
• 2 Multifunctional analog/digital outputs
• several conversion functions included
• especially suited for customer-specific
applications
• Input range and output range selectable via
DIP switches
CMS-BS100 manual rev2.fl.doc